Simon 0600681-039 Instrucciones De Instalación página 7

9. 32A THREE-PHASE SOLUTION CONNECTION
SUMMARY AND DATA
The calculation and sizing of power supply line of the charging point must be
checked by a qualified electrician according to the REBT requirements, taking
into consideration parameters such as the cable length between the electrical
cabinet and the wallbox, and the charging current selected among others. The
values indicated in the following table are indicative:
Connection Term Section
Phase 1 R 10 mm2
Phase 2
S
10 mm2
Phase 3 T 10 mm2
Neutral
N 10 mm2
Ground
T 10 mm2
Bus + (optional)
A 0,25 mm2
Bus - (optional)
B 0,25 mm2
10. COMMISSIONING AND MAINTAINANCE
At the time of commissioning it is necessary to verify the proper functioning of
the equipment by connecting it to an electric vehicle with the appropriate
connector or by using a test equipment. It is recommended to perform the tests
for approximately 10 minutes to consider that the installation has been carried
out correctly.
It is advisable to carry out maintenance tasks that consist basically on performing
a re-tightening of the main power terminals of the wallbox with an annual
frequency depending on the use of the charging point.
The retighten of the screws must be performed in the power part of the charging
circuit and includes:
- Electrical panel where the electrical protections of the wallbox are
located (MCB, RCD and Surge protections).
- Power terminal block inside the wallbox.
- Energy meter.
- Contactors.
11. NETWORK ANALYZER DESCRIPTION
The Wallbox solution of reference 0600681-039 includes a three-phase network
analyzer that complies with the Sub Meter requirements defined in ITC-BT 52
have the ability to measure active and reactive energy, being Class 1 (kWh)
according to standard EN62053-21 and of Class B (kWh) according to standard
EN50470-3, with a 0.5 kWh resolution and certified according to the MID
international standard for legal metrology, referring to the active electrical
energy meters. It can be used for tax metrology (legal).
This three-phase energy analyzer includes a backlit LCD display with integrated
8 digit keypad, with is particularly useful for the measuring of active energy in
applications up to 65 A (direct connection) with dual-rate management
availability.
You can measure the energy consumed and generated or it can be programmed
to only count the energy consumed.
The meter is supplied with the output pulses proportional to the active energy
being measured, Modbus RS 485 port which permits integration with the
electronic Wallbox charge manager and/or with external applications for.
Tracking consumption and charge time of the electric vehicle and detecting
possible anomalies in the electricity network in terms of levels and surges and
overages.
12. DISPLAY READING INSTRUCTIONS
The display is divided into 3 display lines. The engineering units are referred to
the variable shown in the relevant display line. The "negative" symbols (·, dmd)
refer to all the displayed variables. To improve the display legibility, the EM24
uses some symbols. In case of "OVERFLOW", the instrument displays "EEEE": at
the same time the DMD calculation, the hour-counter and the energy meters
functions are inhibited and the alarm outputs are activated. The indication
"EEEE" in a single phase variable automatically implies the overflow condition
of the relevant system variable, and the PF indication is forced to "0.000".
The LCD Display has cursors to scroll in the Measuring or Programming Menus
and has UP and DOWN cursors, which enable you to switch the measuring
Max current value (A) Cable section
32A 1*10 mm2
32A
1*10 mm2
32A 1*10 mm2
32A 1*10 mm2
- 1*10 mm2
- UTP Shielded CAT 5E
- UTP Shielded CAT 5E
mode of the readings from instantaneous values to cumulative values with
the following parameters: Energy Consumed (kWh+), Power (kW), Voltage (V),
Current (A), Power Factor (FP), Frequency (Hz), kvarh+, kvarh-, kW dmd, kW
peak dmd.
1. Joystick
To program the configuration parameters and view the pages of the measured
variables on the display.
2. LED
The flashing red LED is proportional to the measured energy (kWh).
3. Display
LCD-type with alphanumeric indications to:
- display the configuration parameters;
- display all the measured variables.
4. Selector
To select the desired display pages and block programming.
5. Connections
Screw terminal blocks for instrument connections.
13. INSTRUCTION OF USE OF NETWORK ANALYZER
Nombre y descripción del menú
Entering the right password allows accessing the main
PASS?
menu.
CnG PASS It allows changing the password.
APPLiCAt It allows selecting the pertinent application.
It links an ID code to the user of the displayed consumption
USEr
(Three 1-phase independent users by instrument).
It allows selecting the measuring page to be displayed
SELECtor
according to the knob position.
SYS It allows selecting the electrical system.
Ut rAtio VT ratio.
Ct rAtio CT ratio.
It is the integration time used to calculate the demanded
P int.ti
powers.
diG in 1/ diG in 2/
It allows defining the digital inputs function.
diG in 3
duP in Digital input connected to channel A5.
Number of counters transmitted by means of Dupline from
duP Cnt
0 to 6 tiplexer address of the first counter.
Number of the analogue variables transmitted by means of
duP AnA
Dupline from 0 to 8.
duP out. 1/ duP
Alarm function is active only for applications C, E, G and H.
out. 2
It allows selecting the operating range of the digital filter as
FiLtEr.S
% of the full scale value.
FiLtEr.Co It allows selecting the filtering coefficient.
EnE t.rES It allows the reset of all the total counters.
To go back to the measuring mode press the joystick in
End direction 1. Joystick in directions 4 and 5 allows browsing
the programming menu again.
6
Rango
-
-
-
From 1 to 9999
SELEC. 1 (2, 3, LoC)
3P.n; 3P; 3P.1; 2P; 1P
1,0 to 6000
1,0 to 60,00k
1 to 30 min
GAS; Cold; Hot; kWh+Hot;
PrESCAL.1 (ó 2 ó 3) (de 0,1 a
999,9)
no; SYnC; tAr
Adr Cnt; rES Cnt; duP Cnt.n
Adr AnA; duP AnA.n
yes; on AL; off AL; t dEL
1 to 100
1 to 32
-
-