Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special
regenerating
salt,
supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
The softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through 6
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
Water
hardness
Indicator light
0
0-5
0-3
NO
1
Indicator light
6-15
4-9
YES
1
1
Indicator lights
16-30
10-16
2
YES
1,2
Indicator lights
17-25
*3
31-45
YES
1,2,3
Indicator lights
46-60
26-33
4
YES
1,2,3,4
Indicator lights
5
61-90
34-50
YES
1,2,3,4
flashing
"ON/OFF" button
* The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS
off before start this procedure.
1. When the dishwasher is off, OPEN
the door.
2. Hold
down
the
FIRST
and
"THIRD" button (from the left) while
simultaneously pushing the "ON/OFF"
button.
3. Release the buttons when some
"PROGRAMME SELECTION" indicator
lights will come on and an acoustic
signal will sound.
4. Press the "PROGRAMME SELECTION"
button to select the required water
softener level (each time the button is
pressed a light will go on). For level 5,
the 4 "PROGRAMME SELECTION"
indicator lights will flash.
5. Turn off the dishwasher pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
"PROGRAMME SELECTION" indicator lights
4
3
2
1
"PROGRAMME SELECTION" button
10
LOADING THE SALT
On the bottom of the machine there is a
container for the salt for regenerating
the softener.
It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
To add salt, unscrew the cap of the con-
the
tainer on the bottom and then refill the
container.
During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme. The salt
dispenser has a capacity of between 1.5
and 1.8 kg and, for efficient use of the
appliance, it should be refilled from time
to time according to the regulation of the
water softener unit.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
Salt loading indicator
This model is provided with an indicator light
on the control panel which will light up
when it is necessary to reload the salt
container.
IMPORTANT
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
11
Tabla de contenido
