Tabla de contenido
VOLTAGE RELAY
VOLT curr freq v/hz
•
27 Phase Undervoltage
•
59 Phase Overvoltage
•
27TN Neutrl Undervolt
•
59X Overvoltage
•
59N Neutral Overvoltage
•
59D Volt. Diff. 3rd Har.
CURRENT RELAY
volt CURR freq v/Hz
•
46 Neg Seq Overcurrent
•
50 Inst Overcurrent
•
50/27 Inadvertent Energing
•
50BF Breaker Failure
•
50DT Def. Time Overcurr
•
50N Inst Overcurrent
•
51N Inv Time Overcurrent
•
49 Stator Overload
•
51V Inv Time Overcurrent
•
87 Differential Overcurr
•
87GD Gnd Diff Overcurr
•
67N Res Dir Overcurr
FREQUENCY RELAY
volt curr FREQ v/hz
•
81 Frequency
•
81R Rate of Change Freq
•
81A Frequency Accum.
VOLTS PER HERTZ RELAY
volt curr freq V/HZ
•
24 Def Time Volts/Hertz
•
24 Inv Time Volts/Hertz
POWER RELAY
PWR lof fuse dist
•
32 Directional Power
LOSS OF FIELD RELAY
pwr LOF fuse dist
•
40 Loss of Field
V. T. FUSE LOSS RELAY
pwr los FUSE dist
•
60FL V. T. Fuse Loss
PHASE DISTANCE RELAY
pwr lof fuse DIST
•
21 Phase Distance
•
78 Out of Step
FIELD GROUND RELAY
FIELD stator sync
•
64B/F Field Ground
STATOR GROUND RELAY
field STATOR sync
•
64S Stator Ground
SYNC CHECK RELAY
field stator SYNC
•
25S Sync Check
•
25D Dead Volt
BREAKER MONITOR
BRKR trpckt ipslog
•
Set Breaker Monitoring
•
Preset Accumulators
•
Clear Accumulators
TRIP CIRCUIT MONITOR
brkr TRPCKT ipslog
•
Trip Circuit Monitor
IPS LOGIC
brkr trpckt IPSLOG
•
IPS Logic
CONFIGURE RELAY
CONFIG sys stat
•
Voltage Relay
•
Current Relay
•
Frequency Relay
•
Volts per Hertz Relay
•
Power Relay
•
Loss of Field Relay
•
V.T. Fuse Loss Relay
•
Phase Distance Relay
•
Field Gnd Relay
•
Stator Gnd Relay
•
Sync Check Relay
•
Breaker Mon Relay
•
Trip Ckt Mon Relay
•
IPSLogic Relay
SETUP SYSTEM
config SYS stat
•
Input Activated Profiles
•
Active Setpoint Profile
•
Copy Active Profile
•
Nominal Voltage
•
Nominal Current
•
V. T. Configuration
•
Delta-Y Transform
•
Phase Rotation
•
59/27 Magnitude Select
•
50DT Split-phase Diff.
•
Pulse Relay
•
Latched Outputs
•
Relay Seal-in Time
•
Active Input State
•
V.T. Phase Ratio
•
V.T. Neutral Ratio
•
V.T. VX Ratio
•
C.T. Phase Ratio
•
C.T. Neutral Ratio
NOTA: Dependiendo de cuales funciones sean adquiridas,
algunos menús pueden no aparecer.
Figura 3-3 Flujo del Menú Principal
Operación – 3
STATUS
config sys STAT
•
Voltage Status
•
Current Status
•
Frequency Status
•
V/Hz Status
•
Power Status
•
Impedance Status
•
Sync Check Status
•
Breaker Mon Acc Status
•
81A Accumulators Status
•
In/Out Status
•
Timer Status
•
Relay Temperature
•
Counters
•
Time of Last Power Up
•
Error Codes
•
Checksums
VIEW TARGET HISTORY
TARGETS osc_rec comm
•
View Target History
•
Clear Target History
OSCILLOGRAPH RECORDER
targets OSC_REC comm
•
View Record Status
•
Clear Records
•
Recorder Setup
COMMUNICATION
targets osc_rec COMM
•
COM1 Setup
•
COM2 Setup
•
COM3 Setup
•
Communication Address
•
Response Time Delay
•
Comm Access Code
•
Ethernet Setup
Ethernet IP Address
•
SETUP UNIT
SETUP exit
•
Software Version
•
Serial Number
•
Alter Access Codes
•
User Control Number
•
User Logo Line 1
•
User Logo Line 2
•
Clear Output Counters
•
Clear Alarm Counter
•
Date & Time
•
Clear Error Codes
•
Ethernet Firmware Ver.
•
Diagnostic Mode
EXIT LOCAL MODE
setup EXIT
3–5
Capítulos
Tabla de contenido
