Maytag Jenn-Air 8113P752-60 User Guide página 19

Notes:
• The oven control comes from the factory set for Auto
Convect Conversion. When using Convect Bake enter the
conventional baking temperature. The control
automatically converts the temperature to 25° less than
the conventional temperature.
• When using Convect Roast the temperature will not be
automatically reduced. Enter the conventional roasting
temperature and time. The control then lets you know
when 75% of the time has elapsed and alerts you to check
the food for doneness.
• To turn Auto Convect Conversion off, see page 24.
Convect Bake
To set Convect Bake:
1. Press the Convect pad.
2. Select CNVT BAKE using the Quickset pads.
3. Select the oven temperature using the Quickset pads
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
• The temperature can be set from 195° F to 550° F
degrees in 5° increments.
• After three seconds, the oven will begin to preheat. CNVT
BAKE and PREHEAT will appear in the display along with
100° or the actual oven temperature, whichever is higher.
• The temperature in the display will increase in 1°
increments until the oven reaches the preset temperature.
Allow about 15 minutes for the oven to preheat.
• When the oven is preheated, the oven will beep, and
PREHEAT will turn off and CNVT BAKE will be displayed.
AUTO will be displayed if Auto Convect Conversion
feature is turned on.
• Place food in the oven.
4. At the end of cooking, turn the oven off by pressing the
CANCEL pad. Remove food from the oven. The oven will
continue operating until the CANCEL pad is pressed.
Convect Roast
To set Convect Roast:
1. Place food in the oven.
2. Press the Convect pad.
3. Select CNVT ROAST using the Quickset pads.
4. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
• The temperature can be set from 195° F to 550° F
degrees in 5° increments. If Auto Convect Conversion is
turned off, you can set 170° F.
5. Enter desired cook time. Enter the conventional roasting
time using the number pads.
• After three seconds, the oven will begin to heat. CNVT
ROAST will appear in the display along with 100° or the
actual oven temperature, whichever is higher.
• The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature.
• Cook time will begin to count down.
6. At 75% of the cooking time the oven will beep to let you
know to check food. Check food using a meat thermom-
eter. If food is done, take food out of oven and press
CANCEL pad to turn oven off.
7. If food is not done, continue roasting.
Once the set time has elapsed the oven will automatically
go into Keep Warm mode for 1 hour. If
food is taken from the oven before the hour
has elapsed, press CANCEL pad.
Notes:
• If the recipe suggests preheating the oven, add time to
cook time.
• If Auto is off, roast time will not be required.
Rapid Preheat
Use to decrease preheating time when using Bake or Convect
Bake. Use for all foods when baking on one rack.
• After Bake or Convect Bake has been programmed and
activated, press the Rapid Preheat pad.
• 1 RACK ONLY will display, after 10 seconds the display will
show RAPID and PREHEAT.
To return to Standard Preheat:
• Press Rapid Preheat pad again. This will provide standard
preheat and PREHEAT and the selected function will be
displayed.
18
Cont.