lamber L21-RGB Manual De Instrucciones página 26

pushbutton is yellow , this means that the machine is
reaching the good working temperature).
It is possible to interrupt the washing cycle at any time
simply pushing again the wash time selection button
"B".
Rinse will start only at the reached working
temperature. That means that the duration of the
washing cycle you have chosen will be extended up to
having reached the exact temperature (thermocontrol).
G – Extracting the basket, incline and shake it
carefully. So the rest of the water drops will be
eliminated.
Leave the dishes in the basket until they will be dry by
evaporation. Take the dishes away from the basket
and pay attention not to touch the dishes on its border
and put them on clean shelves.
To continue the wash, carry a new basket, introduce it
in the machine, close the door and press button
"C".
- Endless cycle (maximum 15 minutes) : the door
being closed and the cycle put on (any cycle), keep the
button "B" pressed for 3 seconds: lamps 1 and 2 will
flash at the same time (thermocontrol excluded); the
cycle can be interrupted at any time pressing again
button "C" that will let final sequences of pause-rinse
start.
Self-cleaning cycle :
- To switch the machine off press and hold button "A"
for 2 seconds
(Cycle pushbutton is red);
- Remove the overflowpipe from the tank and wait until
it is completely empty
(for machines equipped with drain pump, see the
relative section for instructions),
- Close the hood of the dishwasher
- To switch the machine on
switch "A" for 2 seconds The "C" indicator flashes
yellow
-To begin the self-cleaning process, press and hold
cycle pushbutton "C" for 3 seconds until a solid purple
light turns on,.
After 10 minutes the machine will automatically stop
The "C" indicator light is solid red ;
N.B.: The indicator will switch off
seconds
-Stand by: The machine will automatically stop after
an hour of inactivity (red button "C" will stay lit) .
To resume normal function press the button "A".
DISHES POSITIONING
It is suitable to place dishes, inside the plastic basket
with the concave side facing upwards.
Place mixed cutlery in a vertical position into the
suitable container minding not to cram them and with
handgrips towards the bottom (see drawing).
press and hold main
after nearly 15
ACHIEVEMENTS
Any deficiency in the washing process is apparent
when dirty residuals are visible. An insufficient rinsing
might cause any halos: in this case, check that the
rinsing jets are clean and there is a sufficient pressure
in the water distribution network (ideal is between 2-4
bar).
In the case that residuals are present, check that:
• the washing jets are clean
• there is detergent
• filters are clean
• the position of the dishes in the rack is correct (look
at the specific paragraph).
REGENERATING
(for machines with Water softener)
If the glass-washer is equipped with a Water softener
the regeneration of resins is automatic according to
parameters fixed by the producer (this operation is
signalled by lighting up of led "D").
According to the water hardness, it is possibile to
modify the programming of the regeneration. See the
corresponding table in the installer section.
SALT CONTROL
When it is necessary to add salt in the container, the
lamp "D" flashes.
Unscrew the plug of the salt container at the bottom of
the tank and put 1 kg coarse salt tablets in it. Clean the
gasket and screw the plug.
WARNING!
container damages the machine because of limestone,
besides a defective washing of glasses and dishes.
These damages are not covered by the warranty.
DRAIN PUMP INSTRUCTION
(only for machines with drain pump)
The drain pump starts up automatically just during
the washing cycle to drain the exceeding water
coming from the rinsing cycle.
At the end of the working day, in order to
completely drain the tank, it is necessary to perform
the following operations:
1.Switch the machine off by keeping pressed the main
switch "A" for 2 seconds (cycle pushbutton
becomes red);
2.Open the hood of the dishwasher;
3 .Remove the overflow from the tank;
4.Afterwards push
Pushbutton "C" flashes with sky-blue colour.
26
The lack of salt in the
button "C" for 3 seconds.