Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Installation
INSTALLATION
CAUTION
We strongly
recommend
the removal
of the
old wall sleeve
and the installation
of a new
LGE Wall Sleeve.
If you decide
to keep the existing
wall sleeve,
you have to redirect
the louvers
at the back of
the wall
sleeve
illustration.
The use of pliers is
recommended.
If you DO NOT redirect,
you run
the risk of poor performance
or product
failure.
This is not covered
under the terms of the
LGE
warranty.
• Pick a location
which will allow the conditioned
air
to blow into the area you want. Good
installation
with special
attention
to the proper
position
of the
unit will lessen
the chance
that service
will be
needed.
ITEMS
IN INSTALLATION
HARDWARE
You may not need all parts
in the kit. Discard
unused
parts
ITEM (inches)
Plastic
grille
Horizontal
Insulation
Strips
Around
Insulation Strips
Support
Block
Baffle
Shim
Trim Frame
Washer
Screw
Nuts(Plastic)
Grille Rear
263/4 X 161/2
13/8 X 5/8 X 273/16
13/8 X 13/8 X 273/16
13/8 X 3/4 X 611/2
13/s X 13/s X 611/2
13/4 X 13/8 X 45/16
14 X 41/2 X 1/8
13X
1 X3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
1
HOW TO INSTALL
H
Identify
the existing
wall sleeve before
installing
the unit from the listed below.
Wall Sleeve Dimensions (inches',
Brand
Width
Height
Depth
White-Westinghouse
Frigidaire
25-1/2
15-1/4
16, 17-1/2
or 22
Carrier
(52F series)
General
Electric
26
15-5/8
16-7/8
/Hotpoint
17-1/8
Whirlpool
25-7/8
16-1/2
or 23
Fedders/Emerson
27
16-3/4
16-3/4
or 19-3/4
LGE
25-7/8
15-17/32
16-23/32
Emerson/Fedders
26-3/4
15-3/4
15
Carrier
(51S Series)
25-3/4
16-7/8
18-5/8
Friedrich
27
16-3/4
16-3/4
All wall sleeves
used to mount
the new Air
Conditioner
must be in sound
structural
condition
and have a rear grille that securely
attaches
to
sleeve, or rear flange that serves
as a stop for the
Air Conditioner,
_'1
Remove
old air conditioner
from existing
wall
sleeve.
_-1
Clean
the interior
of an existing
sleeve.
(Do not disturb
seals.)
D
all sleeve
must be securely
fastened
in wall
before installing
the air conditioner.
Use the
nails or screws
through
sleeve into wall, if
needed.
Repaint
sleeve
if needed.
_1_
Prepare
the wall sleeve for installation
of the
unit. If you plan to use your existing
wall
sleeve,
and it is not LGE, use procedure
B or
C below.
Procedure
Brand
Depth(inches)
A
LG E
16-23/32
White-Westinghouse
Frigidaire
Carrier
16, 17-1/2
or 22
(52F series)
B
General
Electric
16-7/8
/Hotpoint
Whirlpool
17-1/8 or 23
Carrier
(51S series)
18-5/8
16-3/4
Fedders/Emerson
or 19-3/4
C
Emerson/Fedders
15
Friedrich
16-3/4
r,_
Install new unit into wall sleeve.
A CAUTION
When
installation
is completed,
replacement
unit
MUST
have a rearward
slope as shown. To achieve
1/4" slope,
remove the backing
from the 11-13/16"
shim strips and attach
them as shown
below
in Fig.
3. Place the higher
portion
of shim to the front of
the rib on base of wall sleeve.
1" highI _
I_"1
I_"1
SHIM PLACEMENT
II 3/4" High
UNiT
Wall Sleeve
FRONT
14 . ..........
UNIT INSTALLATION
FIG. 3
12
Room Air Conditioner
Tabla de contenido
