Special Settings - Novoferm Novomatic 803S Manual De Instrucciones

• Programming the operator
14
Control elements
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver. After the
operator has been programmed, the transparent
cover must be closed again.
A . Numerical display shows the menu stage as well
as the selected value.
a. Point display, lights up to indicate "ready for
operation" and flashes on the hand transmitter
code learning completion.
B . Button during the setting / adjustment phase
serves as an "up" button and outside the menu as
a start button.
C
. Button during the setting /adjustment phase
serves as a "down" button.
D . Button is used to call up the setting/adjustment
menu, to change the menu stages and to store the
settings.
The programming of the control unit is menu-driven.
By pressing button , the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons
selected setting is stored with button
programme jumps automatically to the next menu
stage. By repeatedly pressing button
stages can be skipped. To quit the menu, press
button until "0" is shown again. Outside the menu,
button can be used to generate a start impulse.
Before programming
- Allow door to engage into the carriage.
- Pull out the mains plug. Point display (a) lights up.
- Make sure that the aerial is correctly positioned
(see figure 13).
- Observe the hand transmitter instructions.
15
Menu stage 1: Programming the start
function for the hand transmitter
Briefly press button . "1" is displayed. As soon as
the display flashes, press and keep pressed for
approx. 1 second the button of the hand transmitter,
with which you later wish to start the operator. As
soon as the code has been read, the red point
display (a) flashes five times before quitting.
will be displayed. Menu finished.
Further hand transmitters (up to a maximum of 30)
can be programmed.
16
Menu stage 2: Programming the light
function for the hand transmitter
Press key briefly and figure 1 will be displayed.
Press key once again and figure 2 will be
displayed.
Press the second button at the transmitter with which
the 4-min light is to be switched on. As soon as the
code has been read in, the red point display (a) will
flash 5 times to acknowledge the entry. Figure 0 will
be displayed. Menu finished.
Deleating all the hand transmitters programmed
for the operator:
Plug in the operator's main plug while pressing
button .
17
Menu stage 3: Setting/adjusting the top end-
of-travel position
Keep button pressed for 3 seconds. Number 3
appears in the display 8 a.
Wait a short while until the 3 starts flashing.
Press button and make sure that the door travels in
the OPEN direction.
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
If the door closes in the wrong direction, after
having pressed
!
another 3 seconds. "3" flashes briefly. The
travelling direction is altered.
Now travel by pressing button
end position OPEN 17b.
By pressing button
into direction CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button
the OPEN end-of-travel position and "4" appears in
the display.
18
Menu stage 4: Setting/adjusting the bottom
end-of-travel position
Wait a short while until "4" starts flashing.
Press button . The operator causes the door to
travel in the CLOSE direction as long as the button is
pressed. The position can be altered to the OPEN
direction via button ..
Once the desired CLOSE end-of-travel position has
been reached, press button
the CLOSE end-of-travel position and "0" appears in
the display.
and . The
19
. And the
Force-learning cycle
We recommend setting the suitable door type in
!
, menu
menu stage 8 prior to the force-learning cycle.
During this opening and closing cycle, the
operator learns the force required to open and close
the door. A force limit does not apply!
must not be interrupted. During these cycles must
not be interrupted. During these cycles "0" appears
in the display.
- Press button . The operator causes the door to
open until the top end-of-travel position has been
reached.
- Now press button
the door to close until the bottom end-of-travel
position has been reached.
- After approx. 2 seconds, "0"disappears.
20
Checking the force limit facility
Figure 0
- Place an obstruction (e. g. operator's cardboard
box) underneath the doors's closing edge.
- Starting from the OPEN end-of-travel position,
19
actuate the door to close.
- The door travels towards the obstruction, stops
and travels back to the top end-of-travel position.
19
- The point display (a) must switch off for approx. 1
second. Then the operator functions as normal
again.
If the door springs have been changed or altered,
then the force learning cycle must be repeated:
proceed to menu stage 5 and keep button
pressed for 3 seconds. "0" appears in the display.
Then complete the force learning cycle as explained
under point 19.

• Special settings

In order to access the menus for the special settings,
keep key pressed for 3 sec until figure 3 is
displayed. Press key
Now keep key
displayed. Press key
, keep button pressed for
into the desired door
, the position can be corrected
. The operator stores
. The operator stores
The cycles
again. The operator causes
to by-pass menu step 3.
pressed for 3 sec until figure 5 is
to by-pass menu steps.
After approx. 2 seconds, the display flashes showing
the set value of the opening force limit. The force limit
setting can be increased for decreased via buttons
and . After setting the value, press button
The display shows "6".
Menu stage 6: The closing force limit
After approx. 2 seconds, the display starts flashing,
and the set value for the closing force limit is
displayed.
The force limit setting can be increased or decreased
via buttons and .
After setting the value, press button
in the display.
Finally, check the force settings, and, if necessary,
repeat the setting procedure.
Caution! If the force setting is too high, persons may
be placed at risk of injury.
The factory setting is 4!
Menu stage 7: Light phases
Press button . "7" appears in the display.
Menu Light Warning
value phase phase
0 60 s -
1 120 s -
2 240 s -
3 0 s -
4 0 s 3 s
5 0 s -
6 0 s 3 s
7 90 s 3 s
8 90 s 3 s
9 0 s 8 s
The factory setting is 0.
When the advance warning time is set, the light relay
K will be switched on before the operator starts
running and when the operator is running.
!
Use a auto-flashing warning light.
Menu stage 8: Door fitting
Press button . "8" appears in the display.
The corresponding door type has to be chosen for an
ideal performance and for the optimisation of force.
Menu door type
value
0 Canopy
1 non-swing-out door
2 swinging door, tilting gate (normal run)
3 swinging door, tilting gate (sensitive run)
4 universal setting (factory-set)
5 sectional door featuring draw spring fitting
(Topspeed)
6 sectional door featuring torsion spring fitting
(Topspeed)
7 industrial sectional door feat. normal fitting
8 side sectional door (Topspeed)
9 side sectional door with secondary closing
edges
Subsequently press button . "0" appears in the
display. After changing the door type, the force-
learning cycle 19 is repeated.
GB
.
. "0" appears