Chamberlain 5580 Instrucciones página 14

21
Assemble Door Arm and Set Limits
NOTE: For one-piece doors, do not connect door arm to trolley
before adjusting limits. Failure to follow instructions may result in
damage to door. See below.
A. ONE-PIECE DOOR INSTALLATION:
Connect straight door arm (1) and curved door arm sections (2) to
obtain the longest possible length with hardware (3, 4 & 5). With door
closed, connect straight door arm section to door bracket with a
clevis pin (6). Secure with a ring fastener (7).
Before connecting door arm to trolley, adjust travel limits. Limit
adjustment screws are located on left side panel.
Open Door Adjustment: Decrease up limit. Turn up limit adjustment
screw counterclockwise 4-1/2 turns.
Press door control button. Trolley will travel to full open position (8).
Manually raise door to open position (parallel to floor) and lift door
arm (9) to trolley. The arm should touch trolley just in back of door
arm connector hole (10) as shown in solid line drawing. Increase up
limit if necessary. One full turn equals 7,5cm (3") of door travel.
Closed Door Adjustment: Decrease down limit. Turn down limit
adjustment screw clockwise 4 complete turns.
Press door control button. Trolley will travel to full closed position
(11). Manually close door and lift door arm (12) to trolley. The arm
should touch trolley just ahead of door arm connector hole (10) as
shown in dotted line drawing. Decrease down limit if necessary. One
full turn equals 7,5cm (3") of door travel.
Connect Door Arm to Trolley: With door closed, connect curved arm
to trolley with remaining clevis pin. Secure with ring fastener. NOTE:
Lift door slightly to make connection if necessary.
Run opener through a complete travel cycle. If door has a slight
"backward" slant in full open position, decrease up limits until door
is parallel to floor.
B. SECTIONAL DOOR INSTALLATION:
Connect according to Figure B, then proceed to Step 23.
114A2788C-GB
22
Program your Opener & Remote
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
Your garage door opener receiver and remote control transmitter are
set to a matching code. If you purchase additional remote controls,
the garage door opener must be programmed to accept the new
remote code.
Program the Receiver to Match Additional Remote Control
Codes:
Using the "LEARN" Button
1. Press and release the "learn" button on the motor unit. The learn
indicator light will glow steadily for 30 seconds (1).
2. Within 30 seconds, press and hold the button on the hand-held
remote that you wish to operate your garage door (2).
3. Release the button when the motor unit light blinks. It has learned
the code. If light bulb is not installed, two clicks will be heard (3).
Using the Multi-Function Door Control (optional):
1. Press and hold the button on the hand-held remote that you wish
to operate your garage door (4).
2. While holding the remote button, press and hold the LIGHT button
on the Multi-Function Door Control (5).
3. Continue holding both buttons while you press the push bar on the
Multi-Function Door Control (all three buttons are held) (6).
4. Release buttons when the motor unit light blinks. It has learned the
code. If light bulb is not installed, two clicks will be heard (7).
Now the opener will operate when the remote control push button is
pressed. If you release the remote control push button before the
opener lights flash, the opener has not learned the code.
To Erase all Remote Control Codes
To deactivate any unwanted remote, first erase all codes:
Press and hold the "learn" button on motor unit until the learn
indicator light goes out (approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or keyless entry you wish to
use.
3-Channel Remote:
If provided with your garage door opener, the large button is factory
programmed to operate it. Additional buttons on any rolling code
3-channel remote or mini-remote can be programmed to operate
other rolling code garage door openers or gates.