Pentair Raychem E-100-A Instrucciones De Instalación

HIGH-PROFILE END SEAL INSTALLATION INSTRUCTIONS
APPROVALS
Hazardous Locations
Class I, Div. 2, Groups A, B, C, D
Class II, Div. 2, Groups E, F, G
Class III
– WS
CLI, ZN1, AEx e II T*
Ex e II T*
Ex e IIC T* Gb
E-100-A is IECEx certified for use with:
BTV-CR/BTV-CT:
IECEx
QTVR-CT:
XTV-CT:
KTV-CT:
VPL-CT:
(1)
Except VPL
* For system Temperature Code, see heating cable or design documentation
(2)
Except KTV-CT
KIT CONTENTS
Item Qty Description
A 1 End seal assembly
B 1 Cable lubricant
C 1 End seal label
D 1 Cable tie
WARNING:
This component is an electrical device that must be installed
correctly to ensure proper operation and to prevent shock or fire.
Read these important warnings and carefully follow all of the
installation instructions.
• To minimize the danger of fire from sustained electrical arcing
if the heating cable is damaged or improperly installed, and to
comply with the requirements of Pentair Industrial Heat Tracing
Solutions, agency certifications, and national electrical codes,
ground-fault equipment protection must be used. Arcing may
not be stopped by conventional circuit breakers.
INDUSTRIAL HEAT TRACING SOLUTIONS
E-100-A
(1)
(2)
IECEx BAS 06.0043X
IECEx BAS 06.0045X
IECEx BAS 06.0044X
IECEx BAS 06.0046X
IECEx BAS 06.0048X
.
• Component approvals and performance are based on the use of
Pentair Industrial Heat Tracing Solutions-specified parts only.
Do not use substitute parts or vinyl electrical tape.
• The black heating cable core and fibers are conductive and can
short. They must be properly insulated and kept dry.
• Keep components and heating cable ends dry before and during
installation.
• Bus wires will short if they contact each other. Keep bus wires
separated.
• Use only fire-resistant insulation materials, such as fiberglass
wrap or flame-retardant foam.
• Leave these installation instructions with the user for future use.
EN-RaychemE100Aendseal-IM-H55400 02/15
DESCRIPTION
The E-100-A is a NEMA 4X-rated end seal kit. It is designed for
use with Raychem BTV-CR, BTV-CT, QTVR-CT, XTV-CT, KTV-
CT and VPL-CT industrial parallel heating cables. Once installed,
the end seal is easily re-entered for maintenance; the heating
cable can be accessed without removing the end seal.
This kit may be installed at temperatures as low as –40°F (–40°C).
For easier installation store above freezing until just before
installation.
For technical support call Pentair Industrial Heat Tracing
Solutions at (800) 545-6258.
TOOLS REQUIRED
• Wire cutters
• Slotted screwdriver or nutdriver
ADDITIONAL MATERIALS REQUIRED
• GT-66 or GS-54 glass cloth tape
• Pipe strap
OPTIONAL MATERIALS
• Small pipe adapter for 1 in (25 mm) and smaller pipes:
Catalog number JBS-SPA P/N E90515-000
• For boot replacement order E-100-BOOT-5/PACK P/N 281053-000
Cap
Strain
relief
Boot
Leash
Stand
A
HEALTH HAZARD: Prolonged or repeated contact with the sealant in
the end seal boot may cause skin irritation. Wash hands thoroughly.
Overheating or burning the sealant will produce fumes that may
cause polymer fume fever. Avoid contamination of cigarettes or
tobacco. Consult MSDS VEN 0058 for further information.
CHEMTREC 24-hour emergency telephone:
(800) 424-9300
Non-emergency health and safety information:
(800) 545-6258
• Utility knife
CAUTION:
.
D
C
B
1 / 6