Network Connection; Network Setup; Press Menu On The Remote Control And Select; Connecting To A Wireless Network - JVC LT-39HW45U Manual De Usuario

Chapter 6

Network connection

You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can attach your TV to your LAN using cable in
three ways:
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an external modem
using a Cat 5 cable.
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an IP Sharer, which is
connected to an external modem. Use Cat 5 cable
for the connection.
• Depending on how your network is configured,
you may be able to attach your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable. Note that
the wall outlet is attached to a modem or router
elsewhere in your house.
Select Smart TV > Settings > Interface, then select
Ethernet to connect to a wired network.

Connecting to a wireless network

To connect your TV to your network wirelessly, you
need a wireless router or modem and a Wireless
LAN Adapter. Connect your Wireless High-Gain USB
Adapter (USB dongle) delivered with your TV to your
TV's USB 1 port.
1. Select Smart TV > Settings > Interface, then
select Wireless to connect to a wireless network.
2. Select Wireless setting and press OK/► to enter.
3. Connection Methods: You can setup the wireless
network connection three ways.
- Scan
• Select Wireless setting > Scan, then press
OK/►, the TV will scan all access points within
range. The access points found by the TV will
be displayed.
• Select an available access point, then press
OK/► to connect the TV.
Notes:
- If you select a protected access point, you will
have to enter the corresponding password.
Press OK on the remote control to display the
virtual keyboard to enable you to enter the
password.
- This set has a memory function of available
access point, which enables your set to be
connected to the network even if you switch on
the TV after power off.
- Manual
Select Wireless setting > Manual, then press
OK/►, you will be prompted to enter the correct
SSID of an available wireless router to set up the
connection.
- Auto
If your AP supports WPS (Wi-Fi Protected
Setup), you can connect to the network via PIN
(Personal Identification Number) or PBC (Push
Button Configuration). WPS will automatically
configure the SSID and WPA key in either mode.
Select Wireless setting > Auto, then press
OK/► to enter.
• PIN: Select PIN and press OK/► to enter.
Generate a random PIN code. Make sure this
code is installed on the AP. (For the procedures,
refer to your router manual.) Press OK/► again
to set up the connection.
• PBC: If your router has a PBC push button,
select PBC, then press OK/► to enter. Press
the PBC push button on your router within 2
minutes after you press OK/► again. Your TV
will automatically acquire all the network setting
values it needs and connect to your network.

Network setup

1. Press MENU on the remote control and select

Smart TV > Settings > Internet connection.
Press ◄/► to select On. Wait until the connection
is automatically established.
2. Select Smart TV > Settings > Connection test,
then press OK/► to check the Internet connectivity.
If it does not work, follow below steps to make
sure of the connectivity.
3. Select Smart TV > Settings > IP setting, then
press OK/► to enter the IP setting menu.
- Set Address type to Auto, it will acquire and
enter the needed IP address automatically.
- You can follow below steps to enter your IP
address manually.
• Set Address type to Manual, then press ▼ to
go to the first entry field.
• Enter the IP address, Subnet mask, Default
gateway, Primary DNS and Secondary DNS
values. Use the alphanumeric buttons to enter
numbers and the arrow buttons to move from
one entry field to another.
- After setting, select Smart TV > Settings
> Connection test to check the Internet
connectivity again.
4. Select Smart TV > Settings > Information, then
press OK/► to display the information on current
connection, such as Interface, Address type, IP
address, etc.
Share & See
Note: This manual covers products with either Share
& See or DLNA function. Share & See is DLNA-
compatible.
EN 13
Network connection