OBJ_BUCH-318-007.book Page 17 Tuesday, November 10, 2015 5:05 PM
Technical Data
Rotary Hammer PBH ...
Article number
Speed control
Stop rotation
Right/left rotation
Quick change chuck
Delivery Scope
– Keyless drill chuck
Rated power input
Impact frequency at rated speed
Impact energy per stroke according to
EPTA-Procedure 05/2009
Rated speed
No-load speed
– 1st gear
– 2nd gear
Tool holder
Spindle collar diameter
Drilling diameter, max.:
– Concrete
– Brickwork (with core bit)
– Steel
– Wood
Weight according to EPTA-Procedure
01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745,
EN 50581:2012 according to the provisions of the directives
2011/65/EU, 2014/30/EU, 2006/42/EG.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Helmut Heinzelmann
Executive Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Bosch Power Tools
2800 RE
2900 RE
3 603 C93 0.. 3 603 C93 1.. 3 603 C93 1.. 3 603 C93 2.. 3 603 C94 2..
–
–
W
720
730
-1
min
4000
4000
J
2.6
-1
min
1100
1100
-1
min
0–1450
0–1450
-1
min
–
SDS-plus
SDS-plus
mm
43
mm
26
mm
68
mm
13
mm
30
kg
3.0
/ II
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle
Operate your machine only with the auxiliary handle 17.
Changing the position of the auxiliary handle
(see figure A)
The auxiliary handle 17 can be set to any position for a secure
and low-fatigue working posture.
– Turn the wing bolt for adjustment of the auxiliary handle 16
in anticlockwise direction and set the auxiliary handle 17
to the required position. Then tighten the wing bolt 16
again in clockwise direction.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the depth stop 18.
– Press the button for the depth stop adjustment 15 and in-
sert the depth stop into the auxiliary handle 17.
The knurled surface of the depth stop 18 must face down-
ward.
– Insert the SDS-plus drilling tool to the stop into the SDS-plus
tool holder 3. Otherwise, the movability of the SDS-plus drill-
ing tool can lead to incorrect adjustment of the drilling depth.
2900 FRE 3000 FRE Set
–
–
–
730
750
4000
4000
2.7
2.7
2.8
1100
1100
0–1450
0–1450
–
–
SDS-plus
SDS-plus
43
43
43
26
26
26
68
68
68
13
13
13
30
30
30
3.0
3.0
3.0
/ II
/ II
/ II
1 609 92A 1LU | (23.5.18)
English | 17
3000-2 FRE
–
750
4000
2.8
1100
0–1450
–
0–3000
SDS-plus
43
26
68
13
30
3.3
/ II