Peg-Perego UNO Instrucciones De Uso página 15

6 The stroller basket has three positions. The
normal position can be seen in Figure A.
The basket can be lowered to allow it to be
used even when the backrest is completely
lowered. By pressing on it, it is easier to fill
it without disturbing the baby (fig_b). The
basket can also be raised to allow access to
the rear footboard (fig_c).
7 FRONT BAR: insert the front bar (fig_a) and
press until the first click. Pull the levers under
the front bar towards you (fig_b) and insert it
completely by pushing it forwards (fig_c).
8 The front bar can be lengthened to two
positions. To move it to the first position, pull
the two levers underneath towards you (fig_
a) and pull it until the first click (fig_b). To
move it to the second position, pull the two
levers and the front bar towards you again
until the second click (fig_c). It is dangerous
to put hot drinks on the tray.
9 BRAKE: to brake the stroller, push the brake
levers on the wheels downwards with your
foot, as shown in the figure. Always set the
brake when the stroller is not moving.
1 0 5-POINT SAFETY HARNESS: to attach the
safety harness, insert the two buckles of the
waist strap (with shoulder straps attached
– arrow_a) into the leg divider strap until it
clicks into place (arrow_b). To release, push
the round button placed in center of the
buckle upwards (arrow_c) and pull the waist
strap to the sides (arrow_d).
1 1 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it do the opposite. The waist strap can
be tightened as far as the safety lock (fig_b).
1 2 To adjust the height of the safety harnesses,
release the two buckles on the rear of the
backrest.
Pull the shoulder straps towards you
(arrow_a) until the buckles are released and
insert them in the backrest loops (arrow_b).
Remove the shoulder straps from the sack
(arrow_c) and insert them in the most
appropriate loop (arrow_d), then re-attach
the two buckles on the rear of the backrest
(arrow_e).
1 3 ADJUSTING THE BACKREST: the stroller
backrest can be reclined in three positions.
To lower it, raise the handle (fig_a) and at the
same time lock it into the desired position
(fig_b); push upwards to raise it.
1 4 ADJUSTING THE FOOTREST: the footrest
has two positions. To lower it, pull the two
switches downwards and lower the footrest
at the same time (fig_a). To raise it, pull it up
until it clicks (fig_b).
1 5 SWIVEL WHEELS: the smaller wheels on the
stroller swivel. To make them swivel, raise the
lever (fig_a). Lower the level to set them in
their fixed position (fig_b).
1 6 HANDLEBAR: to make the handlebar
reversible, pull the clips on it upwards at the
same time (fig_a) and move it to the other
side until the final click. IMPORTANT: take
care not to hurt the child's hands or arms
when doing this. Adjust the height of the
handlebar by pressing on both side buttons
at the same time (fig_b).
1 7 DRINK HOLDER: the drink holder can be
attached to both sides of the stroller. Simply
click it into place.
1 8 CARRIAGE AND/OR STROLLER: Uno becomes
a carriage when the backrest is in its lowest
position, the footrest is raised, the handlebar
is on the opposite side to the backrest and the
swivelling wheels are also on the opposite side
to the backrest (fig_a). Uno becomes a stroller
when the backrest is raised, the footrest is
lowered, the handlebar is on the same side as
the backrest and the swivel wheels are on the
opposite side to the backrest (fig_b).
1 9 HOOD: turn back the front edge of the hood
(fig_a), insert the clips in the slots in the
stroller arms (fig_b) and button them to the
rear of the backrest. Button the hood to the
insides of the armrests (fig_c) and stretch it,
lowering the joints (fig_d). To transform the
hood into a sun canopy, open the zip (fig_e)
and unbutton the rest of the hood.
2 0 COVER: to transform Uno into a carriage, first
lengthen the front bar to the second position
and raise the footrest, slide out the lower
part of the cover from under the footrest
sack and insert the tabs of the lower part of
the front cover in the slots of the front bar
(fig_b). The slots in the front bar will come
out when the front bar is lengthened. If
the slots slide back into position, push the
two levers under the front bar towards you.
Finally, slip the side eyelets onto the armrests
(fig_c). The carriage version without a cover
can be seen in Figure D.
2 1 Zip the upper part of the cover to the lower
part, slip the side eyelets onto the armrests in
sequence (fig_a) and button the cover to the
armrests (fig_b). The carriage version with a
cover can be seen in Figure C.
2 2 REMOVING THE WHEELS: to remove the large
wheels, press the button (fig_a) and slide the
wheel out (fig_b). To remove the small wheels,
press the switch inwards (fig_c) and slide out
the wheel at the same time (fig_d).
CLOSING: Before closing the stroller, make
sure that the handlebar is positioned on the
backrest side and ensure that all the wheels
are in the fixed position. If the hood is on,
loosen the joints.
2 3 To close the stroller, press lever 1 and then
lever 2 (fig_a), turn the handlebar forwards
and push it downwards. Complete the
procedure by fastening the clips (fig_b). When
- 15 -