Dolmar AS4030 Manual De Instrucciones página 15

Electrosierra inalámbrica
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 73
Carabiner (rope attachment point)
You can hang the tool by attaching the rope to the cara-
biner. Pull up the carabiner, and then tie it with the rope.
► Fig.10: 1. Carabiner
Spike bumper
The tool is equipped with the spike bumper as stan-
dard. For replacement of the spike bumper, ask Makita/
Dolmar Authorized Service Centers.
When you perform the cutting operation, engage the
spike bumper with the trunk and use it as a lever.
Electronic function
The tool is equipped with the electronic functions for
easy operation.
Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Do not touch the saw chain with
bare hands. Always wear gloves when handling
the saw chain.
Removing or installing saw chain
CAUTION:
The saw chain and the guide bar
are still hot just after the operation. Let them cool
down enough before carrying out any work on
the tool.
CAUTION:
Carry out the procedure of install-
ing or removing saw chain in a clean place free
from sawdust and the like.
To remove the saw chain, perform the following steps:
1.
Release the chain brake by pulling the front hand guard.
Loosen the chain adjusting screw, then the retain-
2.
ing nut.
► Fig.11: 1. Chain adjusting screw 2. Retaining nut
3.
Remove the sprocket cover then remove the saw
chain and guide bar from the chain saw body.
To install the saw chain, perform the following steps:
1.
Check the direction of the saw chain. Match the
direction of the saw chain with that of the mark on the
chain saw body.
2.
Fit one end of the saw chain on the top of the
guide bar.
3.
Fit the other end of the saw chain around the
sprocket, then attach the guide bar to the chain saw
body, aligning the hole on the guide bar with the pin on
the chain saw body.
► Fig.12: 1. Sprocket 2. Hole
4.
Insert the protrusion and the pin on the sprocket
cover to the chain saw body, and then close the cover
so that the bolt and pin on the chain saw body meet
their counterparts on the cover.
► Fig.13: 1. Protrusion 2. Sprocket cover 3. Bolt
4. Pin
5.
Tighten the retaining nut to secure the sprocket
cover, then loosen it a bit for tension adjustment.
► Fig.14: 1. Retaining nut
Adjusting saw chain tension
CAUTION:
Do not tighten the saw chain too
much. Excessively high tension of saw chain may
cause breakage of saw chain and wear of the guide
bar.
CAUTION:
A chain which is too loose can
jump off the bar and it may cause an injury
accident.
The saw chain may become loose after many hours
of use. From time to time check the saw chain tension
before use.
1.
Release the chain brake by pulling the front hand guard.
2.
Loosen the retaining nut a bit to loosen the
sprocket cover lightly.
► Fig.15: 1. Retaining nut
Lift up the guide bar tip slightly and adjust the
3.
chain tension. Turn the chain adjusting screw clockwise
to tighten, turn it counterclockwise to loosen.
Tighten the saw chain until the lower side of the saw
chain fits in the guide bar rail as illustrated.
► Fig.16: 1. Guide bar 2. Saw chain 3. Chain adjust-
ing screw
4.
Keep holding the guide bar lightly and tighten the
sprocket cover.
Make sure that the saw chain does not loose at the
lower side.
5.
Tighten the retaining nut to secure the sprocket cover.
► Fig.17: 1. Retaining nut
OPERATION
Lubrication
Saw chain is automatically lubricated when the tool is in
operation. Check the amount of remaining oil in the oil
tank periodically through the oil inspection window.
To refill the tank, lay the chain saw on its side, then
push the oil tank cap, and then remove the oil tank
cap. The proper amount of oil is 200 ml. After refilling
the tank, make sure that the oil tank cap is tightened
securely.
► Fig.18: 1. Oil tank cap 2. Oil inspection window
After refilling, hold the chain saw away from the
tree. Start it and wait until lubrication on saw chain is
adequate.
► Fig.19
15 ENGLISH
Tabla de contenido
loading

Este manual también es adecuado para:

As4035

Tabla de contenido