Impact Wrench - Chicago Pneumatic CP7748 Serie Manual Del Operador

EN
English (English)
1.Technical Data
Torque
Drive
Working Max
Model
1 2
[ft.lbs] [ft.lbs]
[inch]
[Nm] [Nm]
max. pressure 6.3bar(90psi)
: Blows per minute, k Uncertainty ; L
a
h
Declaration of noise and vibration statement (ISO 15744 and ISO 28927-2)
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared values of other tools
tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured in individual work places may be
higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way the user works, the workpiece and the workstation
design, as well upon the exposure time and the physical condition of the user. We, CHICAGO PNEUMATIC TOOLS , cannot be held liable for the consequences of using the
declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. This tool may cause
hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at www. pneurop.eu/uploads/documents/pdf/PN3-
02-NV_Declaration_info_sheet_0111.pdf. We recommend a programme of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that
management procedures can be modified to help prevent future impairment.
2. Machine type(s)
• This product is designed for installing and removing threaded fasteners in wood, metal and plastic. No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
3. Operation
• Connect device as shown in Fig. 01.
• Fix the accessories properly to the tool.
• To switch rotation, push the switch (B) as shown in Fig. 03
• To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
• To adjust output power, turn the regulator (B) as shown in Fig. 04. (CP7748/CP7748-2)
• Use the reverse switch (B) only when the drive spindle comes to a complete stop. Changing the speed before the drive spindle stops may damage the
machine.
• The CP7748TL is a Torque Limited Impact Wrench intended for initial tightening of wheel lug nuts and bolts. The operator should release the trigger when
impacting begins, and the fastener is snug. Final torque should be applied manually using a calibrated torque wrench, and following the vehicle manufacturer's
instructions.
4. Lubrification
motor
• Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air
line lubricator cannot be used, add air motor oil to the inlet once a day.
Recommended lubricant : CP Oil PROTECTO-LUBE
- 4 oz (0.12l) P/N: CA149661
- 20.8 oz (0.591l) P/N: CA000046
- 1gal (3.8l) P/N: P089507
5. Maintenance instruction
• Follow local country environmental regulations for safe handling and disposal of all components.
• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised
dealer for advice on technical service or if you require spare parts.
• Always ensure that the machine is disconnected from energy source to avoid accidental operation.
• Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn parts.
• High wear parts are underlined in the parts list.
• To keep downtime to a minimum, the following service kits are recommended :
Tune-up kit : see part list
6. Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
7. Declaration of conformity
We :
CHICAGO PNEUMATIC Tool Co. LLC 1800 Overview Drive Rock Hill, SC 29730 - USA
Machine type(s):

Impact Wrench

Declare that the product(s): CP7748/CP7748-2/CP7748TL/CP7748TL-2
Origin of the product : Taiwan
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery"
applicable harmonised standard(s) :
Name and position of issuer :Nicolas Lebreton (R&D Manager)
Place & Date : Saint-Herblain, 24/04/2015
Technical file available from EU headquarter. Nicolas Lebreton R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Original Instructions are in English. Other languages are a translation of the original instructions.
Copyright 2015, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
Inner Hose
Speed Weight
Dia.
3 4 5
[lb]
[min-1] [inch]
[kg]
Sound pressure dB(A), K
pA
EN ISO 11148-6:2012
Air Consumtion
Dimension
L x W x H
Average continuous
H
W
L
6
7
[inch.]
[SCFM]
[mm]
[Nl/s]
= K = 3 dB Uncertainty.
pA WA
Clutch
• Use CP Pneu-Lube synthetic clutch Grease 8940158455 :
0,3 oz. (8,4g).
Serial Number: From 00001 to 99999
CP7748 Series
impact wrench
Sound pressure
Soundpower
Air Inlet
L
L
wA
pA
8 9
[mm] [dB(A)] [dB(A)]
2006/42/EC (17/05/2006)
Vibrations
a k
hd
10 11
[m/s²] [m/s²]