After Use; Motor Brushes - Nilfisk SDH 5120 Instrucciones De Uso

AFTER USE

1 Lift the Operator Handle (6) until it locks in the upright position. NOTE:
The Safety Lock Button (2) will not depress unless the Operator
Handle (6) has been released and tilted back into the operating
position. This will prevent the motor from being engaged while
Operator Handle (6) is in the storage position.
2 Unplug the Power Cord (5) and wrap it around the Handle Release
Latch (4) and the right Operator Handle Grip (1).
3 Check the skirt around the dust control housing. The skirt should be
replaced if it is worn out or torn.
4 Remove the pad from the machine. Clean the pad and hang it up to
dry. Allow buffing pads to dry completely before using again.
5 Wipe the entire machine with a clean, damp cloth.
6 Inspect the entire machine and all accessories for damage. Perform
any required maintenance or repairs before storage.
7 Store the machine in a clean, dry place with the Operator Handle (6)
locked in the upright position.
MAINTENANCE
C - AIR FILTER
The air filter "A" on top of the motor should be cleaned at least once a week.
To clean the filter, slide the motor cover "B" forward and lift up and off. Pull
the filter off and wash with warm water and allow it to dry completely before
putting it back on the machine (or blow clean with compressed air).
D - DUST COLLECTION BAG
The dust collection bag should be removed and replaced after about every 20
hours of use. Tip the machine back onto it's handle (6), the same as you would
if you were changing the pad. Squeeze in on the sides of the bag cover "A"
and remove it from the machine. Remove the dust bag "B" (being careful not
to spill any debris) and discard. Tip the machine back upright. Push in on the
sides of the new bag "B" to pop-it-open and install it by pushing it down (grip
the cardboard base of the bag) onto the (2) tubes protruding from the base.
Re-install the cover "A".
TECHNICAL SPECIFICATIONS (as installed and tested on the unit)
Model
Model Number
Voltage/frequency
Rated Power
Protection Class (electrical)
Protection grade (mec, moist, dust)
Sound Pressure Level (at 1.5m)
Vibration at the Hand Controls
56201504 / 56201800
V/Hz 220-240V/50/60Hz
W
dB(A)/20µPa
m/s 2

MOTOR BRUSHES

This machine is equipped with a motor brush wear indicator light. If this light
comes on during use, contact your local Nilfisk-Advance distributor to have
the motor serviced.
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a similarly qualified person in order to avoid a hazard.
CAUTION!
The motor can be severely damaged if the machine is used for
an extended period of time with the light glowing.
TROUBLESHOOTING
SWIRL MARKS
• Floor not clean.
• Area not properly swept - debris in pad or brush.
• Improper pad for the job.
• Moving the machine too fast.
CIRCLES ON THE FLOOR
• Machine standing still while the pad is running.
FLOOR FINISH REMOVED
• Improper pad...too aggressive.
• Moving the machine too slowly.
MACHINE WOBBLES DURING OPERATION
• Defective pad... one side is more dense than the other.
• Machine left sitting on pad for extended period of time causing pad to
"take a set".
• Pad not "seated" properly into pad holder bristles.
• Padholder out of balance - replace.
MACHINE DOES NOT RUN
• Check plug for proper connection - on machine and at wall outlet.
• Check building circuit breaker.
• Call for service.
SDH 5120
1250
IP 30
<71.5
<2.5m/s 2
revised 2/00 FORM NO. 56041370 / SDH 5120 - 25