Bodum 11659 Instrucciones De Uso página 4

hot surfaces.
Unplug the power cord from the wall outlet when the kettle is
not in use and before cleaning. Allow the kettle to cool before
putting on or taking off parts, and cleaning it.
Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions, or has been damaged
in any manner. Return appliance to the nearest authorized
service facility for examination, repair or adjustment.
Never attempt to exchange the mains cable of the appliance
as special tools are required for this. To ensure continued
safety of the appliance, if the cable needs to be repaired or
exchanged, have this carried out exclusively by a customer
service workshop authorised by the manufacturer.
To protect against fire, electric shock and injury to persons
do not immerse cord, plug, kettle container and power base
in water or other liquid.
Scalding may occur if the lid is removed during the brewing
cycles.
Make sure the lid is always closed when boiling.
Save theSe inStructionS
inStaLLation
Place the appliance on a stable flat
surface which is neither hot nor
near a heat source. The surface
must be dry. Keep the appliance
and its mains cable out of reach of
children.
During use, do not place the base
unit (6) on a metal tray or a metal
surface.
Ensure that the voltage indicated
on the rating plate of the appliance
agrees with the mains voltage in
your area. Connect the appliance
2
only to
a properly earthed power point with
a minimum output of 12.5A. (Use
a residual current device (RCD) seek
the advice of an electrician.) While
the appliance is in use, the mains
plug must be accessible in case
of an emergency. The manufacturer
declines any liability for accidents
caused by faulty or non-existing
earthing of the appliance.
If the power point is unsuitable for
accommodating the plug of your
appliance, have the power point
changed by a licensed electrician.
PartS oF the KettLe
1 Hinged lid
2 Scale filter
3 Water level gauge
4 Max water level indicator
5 Min water level indicator
6 Base unit
7 ON/OFF button
8 Temperature selection knob
9 Keep warm button
10 Sensor element
SPeciaL inStructionS
Power cord
A short power-supply cord is to be
provided to reduce risks resulting
from becoming entangled in or
tripping over a longer cord.
Extension cords are available and
may be used if care is exercised in
their use.
If an extension cord is used, the
marked electrical rating of the
extension cord should be at least
as great as the electrical rating of
the appliance, if the appliance is of
the grounded type, the extension
cord should be grounding type
3-wire cord. The longer cord
should be arranged so that it will
not drape over the counter top or
table top where it can be pulled
on by children or tripped over
unintentionally.
Switching off the kettle manually
The ON/OFF button (7) can be used
to switch the kettle off before the
water has reached the required
temperature.
Safety cut-off
The kettle is protected against
damage resulting from use with an
insufficient volume of water. A safety
cut-off will automatically disconnect
power supply if the heating
its
element overheats. Should the
kettle ever boil dry during operation,
you must leave it to cool for 10
minutes before refilling it with cold
water. The safety cut-off will reset
automatically once it has cooled.
BeFore uSinG the KettLe
Clean the kettle before using
it for the first time by filling it
completely (to the MAX mark) (4)
with water, boiling the water, and
then discarding the water.
hoW to uSe the KettLe
Filling the kettle
Remove the kettle from its base (6).
Open the lid (1), fill the kettle with
water to the desired level then close
the lid (1). The kettle must contain a
minimum of 0.25 l (5) and should be
filled no higher than the MAX mark
(4). This prevents it from switching
off before the water has boiled or
reached the required temperature.
connecting to the electrical supply
After filling the kettle, place it on its
base (6). Check the kettle is properly
seated on the base (6).
Connect the kettle to the electrical
supply; an acoustic signal indicates
that it is ready.
Now select the required water
temperature by turning the
temperature selection knob (8)
3