GGP ITALY CA 434 Manual De Instrucciones página 19

EN
STANDARDS OF USE
For instructions regarding the engine and the battery (if
supplied), read the relevant manuals.
1. FINISH ASSEMBLY
NOTE – The machine can be supplied with some of the
components already fitted.
1.1
To mount the stone-guard (1), the left end of the pin (2)
must be pushed through and then inserted in the hole of the
left-hand (3) on the chassis. Line up the other end of the pin
with the relative hole in the right-hand support (4). Using a
screwdriver, push the pin into the hole so that the groove (5)
can be reached. Fit the snap ring (6) into the groove and hook
on the right (7) and left (8) springs, as shown.
1.2
Return the lower part of the handle, which is made up
of two pre-assembled elements (1), to its working position and
lock into place using the lower knobs (2). Attach the upper part
(3) using the screws (4) supplied, ensuring that the spiral (5) of
the starter cable is in the correct position.Attach the control
cables using the clips (6).
By loosening the knobs (2) the handle can be set at three dif-
ferent heights.
1.3
Assemble the dashboard (1) following the steps shown.
1.4
With the plastic part (2) upside down, fit all the slots
along the edge (3) of the cloth (1) onto the hooks (4) of the
plastic part, starting from one end. Put the two side parts of
the frame (5) through the loops in the cloth. Insert the two ends
of the frame (5) in their seats and hook the plastic bar (6) onto
the central part of the frame.
Secure the frame to the plastic part using the screws (7).
1.5
On models with an electric starter, connect the battery
cable to the lawnmower's general cable connection.
2. DESCRIPTION OF CONTROLS
2.1
The throttle (where fitted) is controlled by the lever (1)
and positioned as shown on the relative plate. Some models
have a fixed speed, and therefore no need of a throttle (2).
2.2
The blade brake is controlled by the lever (1), which
should be held against the handle when starting and using the
lawnmower.The engine stops when the lever is released.
2.3
In power-driven models, draw the lever (1) towards the
handle for forward movement. The lawnmower stops moving
forward when the lever is released.
2.4
The cutting height is adjusted using the levers (1).
The four wheels must be at the same height.
MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE HAS
STOPPED MOVING.
3. GRASS CUTTING
3.1
Lift the stone-guard and attach the grass-catcher (1)
correctly as shown in the drawing.
3.2
To start the engine, follow the instructions in the
engine booklet and then pull the blade brake lever (1) towards
the handle and give a sharp pull on the starter cable knob (2).
For models with an electric starter, turn the starter key (3).
3.3
The lawn will look better if it is always cut to the same
height and in alternate directions.
3.4
When you have finishing mowing, release the brake
lever (1) and disconnect the spark plug cap (2). Remove the
starter key (3) (where fitted). WAIT FOR THE BLADE TO STOP
before carrying out any type of work on the machine.
4. ROUTINE MAINTENANCE
IMPORTANT – Regular, careful maintenance is essential
for keeping the safety level and original performance of
the machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, mainte-
nance or adjustment operation on the machine.
2) Carefully clean the machines with water after each cut;
remove the grass debris and mud accumulated inside the
chassis to avoid their drying and thus making the next
start-up difficult.
3) The paintwork on the inside of the chassis may peel off in
time due to the abrasive action of the cut grass; in this
case, intervene promptly by touching up the paintwork
using a rustproof paint to prevent the formation of rust that
would lead to corrosion of the metal.
4) Should it be necessary to access the lower part, only tilt the
machine from the side shown in the engine handbook; fol-
lowing the relative instructions.
5) Do not drip petrol onto the plastic parts of the motor or the
machine to prevent damaging them and remove all traces
of spilt petrol immediately. The warranty does not cover
damage to plastic parts caused by petrol.
4.1
All operations on the blade should be carried out at a
specialized centre.
Note for specialized centres: Reassemble the blade (2) as
shown in the drawing and tighten the central screw (1) using a
torque wrench set to 35-40 Nm.
4.2
In power-driven models:
• adjust the tension of the belt with the nut (1) to get the right
measurement (6 mm).
• turn the adjusting nut (2) so that the wire (3) is slightly loose
and the lever (4) is idle.
4.3
To recharge a flat battery, connect to the battery
charger (1) following the instructions in the battery mainte-
nance handbook. Do not connect the battery charger directly
to the engine terminal. It is not possible to start the engine
using the battery charger as a power source, as it may get
damaged. If the machine is to remain inactive for a long peri-
od, disconnect the battery leads after making sure that the
battery is fully charged.
Should you have any doubts or problems, do not hesitate to
contact your nearest Service Centre or your Dealer.
17