Pleasant Hearth LWS-127201 Manual De Usuario página 14

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR FRESHEN UP A
FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS
WELL AWAY FROM THE HEATER WHILE IT IS IN USE.
GLASS CARE
The following use and safety tips should be observed:
1. Inspect the glass regularly for cracks and breaks.
If you detect a crack or break, extinguish the fire
immediately, and contact your dealer for replacement.
2. Do not slam door or otherwise impact the glass.
When closing doors, make sure that logs or other
objects to not protrude and impact the glass.
3. Do not clean the glass with materials which may
scratch (or otherwise damage) the glass. Scratches
on the glass can develop into cracks or breaks.
4. Never attempt to clean the glass while unit is hot. If
the deposit is not very heavy, normal glass cleaners
are adequate with a plain, non-abrasive scouring pad.
Heavier deposits may be removed with the use of a
readily available oven cleaner.
5. Never put substances which can ignite explosively in
the unit since even small explosions in confined areas
can blow out the glass.
6. This unit has an airwash system, designed to reduce
deposits on glass.
7. Deposits may build on the glass during normal
operation and use. Normal glass cleaners work well
to remove these deposits. Heavier deposits may be
removed by using a damp cloth dipped in wood
ashes or by using a commercially available oven cleaner.
REPLACE GLASS ONLY WITH GHP GROUP
5MM CERAMIC GLASS (SEE REPLACEMENT
PARTS PAGE 18).
GLASS REPLACEMENT
CAUTION: Make sure fire is out and stove is completely
cool to the touch.
1. Find an area that will ensure safe removal and no
damage to surface of door frame or decorative home fur-
nishing.
2. Wearing a pair of protective gloves, remove the push
nuts that retain the door pins from being pulled out and
then lift the door off of the hinges.
3. Lay the door face down on a protective surface locat-
ed in Step 2.
4. Remove the screws from all glass retainers and
remove the broken glass, ensuring that the door frame
is free from any slivers. (If even small slivers are left, the
new glass will not seal correctly causing the stove to
burn improperly.)
5. Attach glass gasket (from GHP Group replacement
parts page 18) to new glass and install in door frame.
6. Replace glass retainers with screws making sure not
to cross thread or overtighten.
7. Place door on hinges and replace new push nuts,
purchased from GHP Group, on door pins to ensure door
does not move after reinstall.
GASKET REPLACEMENT
After extensive use, the sealing material which provides
glass and door seal may need to be replaced if it fails to
sustain its resilience. Inspect glass and door seal period-
ically to ensure for proper seal. If gaskets become frayed
or worn, replace immediately.
Contact your dealer or GHP Group Customer Service for
approved replacement parts. The following steps should
be followed for glass gasket replacement:
1. Ensure appliance is not in operation and is thoroughly
cooled.
2. Remove screw and glass clip.
3. Lift glass out from glass clip.
4. Remove old gasket and clean glass.
5. Replace new gasket starting at the bottom of glass
working along edges, being sure to centre gasket
channel on glass.
6. Trim to length and butt ends together.
7. Replace glass in door, being sure not to over-tighten
screw and clip.
The following steps should be followed for door gasket
replacement:
1. Ensure appliance is not in operation and is thoroughly
cooled.
2. Remove old door gasket and clean channel.
3. Using an approved high temperature gasket cement,
apply a thin coat in bottom of channel.
4. Starting at hinge side of door, work into channel
around door unit, end butt and trim to length.
5. Close door and allow three to four hours for cement
to set before restarting appliance.
Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture
to form creosote. The creosote vapors condense in the
relatively cool chimney flue of a slow-burning fire. As a
result, creosote residue accumulates on the flue lining.
When ignited this creosote makes an extremely hot fire.
The chimney connector and chimney should be inspect-
ed at least once every two months during the heating
season to determine if a creosote buildup has occurred.
If creosote has accumulated (3 mm or more) it should be
removed to reduce the risk of a chimney fire.
13
CREOSOTE