EINHELL GE-CS 18 Li-Solo Manual De Instrucciones Original página 22

Protection from environmental infl uences
1. Wear suitable work clothes. Wear safety gog-
gles.
2. Protect your cordless tool and the battery
charger from moisture and rain. Moisture
and rain can cause dangerous cell damage.
3. Do not use the cordless tool or the battery
charger near vapors and infl ammable liquids.
4. Use the battery charger and cordless tools
only in dry conditions and an ambient tempe-
rature of 10-40°C.
5. Do not keep the battery charger in places
where the temperature is liable to reach over
40°C. In particular, do not leave the battery
charger in a car that is parked in the sunshine.
6. Protect batteries from overheating. Over-
loads, over-charging and exposure to direct
sunlight will result in overheating and cell
damage. Never charge or work with batteries
which have been overheated – replace them
immediately if possible.
7. Storage of batteries, battery chargers
and cordless tools. Store the charger and
your cordless tool only in dry places with an
ambient temperature of 10-40°C. Store your
lithium-ion battery pack in a cool, dry place at
a temperature of 10-20°C. Protect them from
humidity and direct sunlight. Only place fully
charged batteries in storage (charged at least
40%).
8. Prevent the lithium-ion battery pack from free-
zing. Battery packs which were stored below
0°C for more than 60 minutes must be dispo-
sed of.
9. When handling batteries beware of electro-
static charge: Electrostatic discharges cause
damage of the electronic protection system
and the battery cells. Avoid electrostatic char-
ging and never touch the battery poles.
Rechargeable batteries and cordless electric
machines and tools contain materials that are po-
tentially harmful to the environment.
Anl_SA_GE_CS_18_Li.indb 22 Anl_SA_GE_CS_18_Li.indb 22
GB
Special safety instructions
•
Check that the speed shown on the grinding
tool is the same as, or faster than, the rated
speed of the grinder.
•
Check that the dimensions of the grinding tool
match those of the grinder.
•
Grinding disks must always be used and
stored with care in accordance with the inst-
ructions of the manufacturer.
•
Always check the grinding disk before use.
Never use any disks with pieces broken off,
which are cracked or are in any other way da-
maged.
•
Check that grinding tools are attached in
accordance with the instructions of the manu-
facturer.
•
Always use backing layers if they are supplied
with the grinding tool and their use is speci-
fied.
•
Check that the grinding tool is properly at-
tached and fastened before use and allow
to run without load in a safe position for 30 s.
Stop immediately if it should vibrate heavily or
if any other fault should become apparent.
Examine the machine to find the cause of the
fault.
•
Never use the electric tool without the guard if
a guard is included in delivery.
•
Do not use separate reducer sleeves or adap-
ters to make grinding disks with large holes fit
properly.
•
For grinding tools with threaded inserts,
check that the thread is long enough for the
length of the spindle.
•
Ensure that the tool is securely fastened.
•
Take care to ensure that any sparks genera-
ted during use do not cause any danger, e.g.
by hitting persons or igniting inflammable
substances.
•
Take care to ensure that the air vents are not
blocked whenever you carry out work invol-
ving the generation of dust.
•
Use safety goggles and ear-muffs.
•
You should also wear protective clothing and
equipment such as a dust mask, work gloves,
apron and helmet.
•
The grinding tool runs on after the tool is
switched off.
•
Do not use any saw blades.
Always keep these Safety Instructions in a
safe place.
- 22 -
21.07.2016 08:16:46 21.07.2016 08:16:46