Tectro R232TC Instrucciones De Uso página 26

REPLACEMENT OF THE WICK
1
L
ENSURE THAT THE HEATER IS OFF AND COMPLETELY
COOL BEFORE STARTING TO REPLACE THE WIC K.
1. Press the shutoff button ①, lower the wick, take out the refueling tank ⑨,
2
2. Remove the 4 screws off the body.
3. Hold the right and left handles and tilt down the body slightly forward. Now lift up
4. Hold the flame baffle by its righe and left and release the hooks from the square
5. Remove the 4 wing nuts from the wick cylinder.
3
6. Pull out the wick cylinder upward and place it on top of the fuel tank. Handle the
7a.Remove the screw from the Tip-over automatic extinguish device.
7b.With your righe hand, pull the Tip-over automatic extinguish device in the
4
8. While pulling the coupler to the right ( in the direction of arrlw), insert a new wick
9. Set up the wick cylinder. Temporarily apply and tighten the 4 wing nuts. Make
5
6
7a 7b
4
26
ENSURE THAT THE HEATER IS OFF AND COMPLETELY COOL BEFORE
STARTING TO REPLACE THE WICK.
1. Press the shutoff button 1, lower the wick, take out the refueling tank 9,
remove the combustion chamber ④ and batteries, and pull out the wick
remove the combustion chamber 4 and batteries, and pull out the wick
adjustment knob ②.
adjustment knob 2.
2. Remove the 4 screws off the body.
3. Hold the right and left handles and tilt down the body slightly forward.
Now lift up the body to get it free.
the body to get it free.
4. Hold the flame baffle by its righe and left and release the hooks from the
square holes. Divide the flame baffle in the right and left halves in the
holes. Divide the flame baffle in the right and left halves in the directions of
directions of arrows (a) and (b).
arrows (a) and (b).
5. Remove the 4 wing nuts from the wick cylinder.
6. Pull out the wick cylinder upward and place it on top of the fuel tank.
Handle the cylinder with care because the igniter lead is still connected.
cylinder with care because the igniter lead is still connected.
7a. Remove the screw from the Tip-over automatic extinguish device.
7b. With your righe hand, pull the Tip-over automatic extinguish device in the
direction of arrow to remove the wick up/down fixture out of the hole in
direction of arrow to remove the wick up/down fixture out of the hole in the wick
the wick holder bracket. With your left hand, draw out the wick upward.
holder bracket. With your left hand, draw out the wick upward.
8. While pulling the coupler to the right (in the direction of arrlw), insert a
new wick into the wick guide and turn the wick until the tip of the wick
into the wick guide and turn the wick until the tip of the wick up/down fixture
up/down fixture goes into the hole of the wick holder bracket.
goes into the hole of the wick holder bracket.
In fitting the new wick, be careful not to deform the wick holder.
In fitting the new wick, be careful not to deform the wick holder.
9. Set up the wick cylinder. Temporarily apply and tighten the 4 wing nuts.
Make sure the clearance (through which the wick goes up and down )
sure the clearance (through which the wick goes up and down ) between the
between the wick cylinder and the wick guide is uniform all around. Now
wick cylinder and the wick guide is uniform all around. Now tighten up the wing
tighten up the wing nuts diagonally.
nuts diagonally.
In setting up the wick cylinder, be careful not to get the lead caught.
In setting up the wick cylinder, be careful not to get the lead caught.
8 9
clearance