GRE SEL.E4 Manual De Instrucciones página 16

8.6 Cycle of the machine
Between each change of polarity the box Between each change of polarity the box
displays "00" and the + and - indicators light
up for about 2 minutes.
After each reverse polarity time, the unit After each reverse polarity time, the unit
indicates indicates its its maximum maximum
minutes then returns urns
adjustment.
8.7 Verification and maintenance Verification and maintenance
Error signals:
If there is a problem with electric current, voltag If there is a problem with electric current, voltage
or internal temperature, the machine no longer or internal temperature, the machine no longer
displays anything.
Only the indicator stays lit.
The machine will start up again automatically.
Adding salt:
Check the salt concentration. If the concentration Check the salt concentration. If the concentration
is less than 4g/l add salt, using the following is less than 4g/l add salt, using the following
equation:
Q = (4 - T) x V
Q = quantity of Kg of salt to add
4 = correct salt concentration
T = concentration recorded in the pool recorded in the pool
V = pool volume in m3.
Always stop the chlorinator before adding any Always stop the chlorinator before adding any
product whatsoever. Wait until the salt has product whatsoever. Wait until the salt has
dissolved before turning the chlorinator back on dissolved before turning the chlorinator back on
again.
The salt concentration should be checked at The salt concentration should be checked at
least twice a year.
Winterization:
If pool filtration is maintained during the winter If pool filtration is maintained during the winter
months, we recommend turning off the chlorinator months, we recommend turning off the chlorinator
when the water temperature drops below 15°C, when the water temperature drops below 15°C,
removing the electrode from the chamber, and removing the electrode from the chamber, and
replacing it with the cap that has been provided for replacing it with the cap that has been pro
this purpose.
Tips for proper use of the electrode: Tips for proper use of the electrode:
The electrode is a wear-sensitive part, and its life
span depends on the following factors: span depends on the following factors:
- Salt concentration:
Never run the chlorinator with a salt concentration Never run the chlorinator with a salt concentration
less than 3.5 g/l.
- Water temperature and winterization: er temperature and winterization:
Turn off the machine whenever the water Turn off the machine whenever the water
temperature drops to 15°C or below. temperature drops to 15°C or below.
- Adjustments:
Never leave the machine on maximum production Never leave the machine on maximum production
unless unless there there is is a a
indicators light
current current during during
to to the the previous previous
gain automatically.
sensitive part, and its life
chlorine chlorine shortage. shortage. An An
101449 Installation and user manual
"economical" setting would be about 75% of the "economical" setting would be about 75% of t
maximum current value printed on the side label. maximum current value printed on the side label.
- Reverse polarity:
Your machine is adjustable (see heading 7.5 ). Your machine is adjustable (see heading 7.5 ).
The electrode's life span depends on the number The electrode's life span depends on the number
of changes of polarity performed. For example, it
of changes of polarity performed. For example, it
2 2
will wear out less quickly if change of polarity will wear out less quickly if change
occurs every 6 hours, and more rapidly if it occurs every 6 hours, and more rapidly if i
occurs every 2 hours.
Scale-covered or furred-
The electrode should be clean The electrode should be clean-looking, without any
scaling.
If this should be the case, de If this should be the case, de-scale the electrode
by dipping it in a solution of 80% water and 20%
hydrochloric acid. Next, check the reasons for this hydrochloric acid. Next, check the reasons for this
furring-up:
• the pH is too high
• the salt concentration is too low the salt concentration is too low • the setting for change of polarity is too long the setting for change of polarity is too long
• the electrode is worn out the electrode is worn out
Compatibility:
The sterilizing
produced by the machine is compatible with most duced by the machine is compatible with most
pool water treatment products except for PHMB pool water treatment products except for PHMB
polymers. In any case, when adding products, turn polymers. In any case, when adding products, turn
off the chlorinator until the products are com tor until the products are completely
dissolved.
Washing the filter/draining the pool:
Turn the machine off when handling the filter Turn the machine off when handling the filter
valve: washing, rinsing, draining, except if a flow valve: washing, rinsing, draining, except if a flow
switch is installed.
Flow switch error:
In the case of a flow shortage, the machine In the case of a flow shortage, the machine
indicator will blink and display "99". indicator will blink and display "99".
manual
-up electrode:
a solution of 80% water and 20%
agent gent (sodium (sodium hypochlorite) hypochlorite)
draining the pool:
16