Safety Information; Assembly And Installation - MCS Master TR 3C Manual De Instrucciones

►►1. SAFETY INFORMATION
en
(Fig. 1)
This series of warm air heaters is particularly suited to heating
it
areas, such as warehouses, shops, restaurants and homes.
These heaters comply with the current European directive.
de
IMPORTANT: You are required to read and understand this
operational manual prior to assembling, starting up or con-
es
ducting maintenance on this heater. Using the heater incor-
rectly can cause serious injury. Keep this manual for future
reference. fr
IMPORTANT: This heater is not suitable for use by persons
nl
(including children) with reduced physical, sensory or men-
tal capacities or with lack of experience or knowledge un-
pt
less supervised by a person responsible for their safety.
Children must be supervised to make sure they do not play
with the heater.
da
IMPORTANT: In order to prevent any risk, even if power
fi
supply mains disconnection is foreseen, all cleaning,
maintenance and repair operations requiring access to
no
dangerous parts (e.g. replacing the damaged power supply
cable), must be carried out by the manufacturer, its technical
support centre, a person with similar qualification.
sv
pl IMPORTANT: Comply with all local legislation and current
regulations when using the heater.
►1.1. Heaters used near tarpaulins, curtains or other similar
ru
covering materials must be a safe distance from them. It is
advised to use fire-proof covering material.
cs
►1.2. Keep the heater a safe distance from humidity, water and
atmospheric agents to prevent serious damage to the heater.
hu
►1.3. Keep the hot parts of the heater a suitable distance from
inflammable or thermolabile materials (including the power
supply cable).
sl
►1.4. Do not handle or conduct maintenance on the heater
when it is hot, connected to the mains or in operation.
tr
►1.5. For correct use, install the wall heater using suitable
fixing plugs. The wall used for installation must be adequate
hr
to support the weight of the heater. DO NOT USE THE HEATER
WHILE PLACED ON THE GROUND.
►1.6. Keep animals at a safe distance from the heater.
lt
►1.7. Power on the heater only with a current which has the
voltage and frequency values specified on the heater's identi-
lv
fication plate.
►1.8. Make sure the heater is only connected to suitable
et
mains with a differential switch and suitable earthing.
►1.9. If the power supply cable or the remote room thermostat
ro
are damaged, they must be replaced by a technical support
centre to prevent any risk.
►1.10. Disconnect the heater from the mains power supply
sk
when not in use for a prolonged time.
►1.11. Always disconnect the heater from the mains if tem-
bg
porarily left in unsafe conditions and in any case make sure it
cannot be used.
uk
►1.12. Never block, not even partially, the heater's air vent
(rear) or the air outlet (front).
►1.13. Avoid ducting the air.
bs
►1.14. Do not cover the heater while in operation, it might
overheat.
el
►1.15. Ask the technical support service to check that the
heater is working properly at least once a year and/or as re-
zh
quired.
THE MANUFACTURER DECLINES ANY LIABILITY FOR
DAMAGE/INJURIES TO PROPERTY/PERSONS DERIVING
FROM IMPROPER USE OF THE HEATER.
ONLY SPECIALISED PERSONNEL AUTHORISED BY THE
MANUFACTURER CAN PERFORM WORK ON THE HEATER.
►►2. UNPACKING
WARNING: The packaging material is not a toy. Keep
the plastic bag out of the reach of children; danger of
suffocation!
►2.1. Remove all packaging material used to deliver the heater
and dispose of it in compliance with current standards.
►2.2. Remove all items from the packaging.
►2.3. Check for any damage incurred during transport. If the heat-
er appears damaged, immediately inform the dealer from whom it
was purchased.
►►3. DESCRIPTION
(Fig. 2)
A. Wall support.
B. Adjusting screw.
C. Fastening screw.
D. Heater.
E. Main power supply switch.
F. Reset.
G. Power supply cable.
H. Remote room thermostat.
I. Room thermostat display.
L. Remote room thermostat temperature sensor.
►►4. ASSEMBLY AND INSTALLATION
(Fig. 3)
For the assembly and installation of the heater, carefully follow the
instructions below.
The mechanical parts, which come with the relative nuts and bolts,
are always in the heater's packaging and must always be assem-
bled before the product is turned on.
THE HEATER MUST BE INSTALLED ACCORDING TO LAW, US-
ING COMPONENTS IN COMPLIANCE WITH LOCAL AND/OR
NATIONAL REGULATIONS. THE MANUFACTURER DECLINES
ANY LIABILITY FOR DAMAGE/INJURIES TO THE HEATER
AND/OR PERSONS DERIVING FROM INCORRECT INSTALLA-
TION.
►►5. OPERATION
WARNING: You are required to read, understand and follow
the ''INFORMATION ON SAFETY'' before starting the heater
in order to use it correctly and avoid risks.
WARNING: Make sure the power supply cable is intact and
that the features of the mains power supply match the ones
on the heater's technical data plate.
WARNING: Never use the heater without first assembling
all the components correctly. For correct use, install the
wall heater using suitable fixing plugs. The wall used for
installation must be adequate to support the weight of the
heater. DO NOT USE THE HEATER WHILE PLACED ON THE
GROUND.
►►5.1. SWITCH-ON:
►5.1.1. After installing the wall heater, connect the heater plug to
the electrical mains (Fig. 4) and set the main power switch to "I /
ON". The display shows the room temperature.
►5.1.2. Turn on the heater using the "ON / OFF " button of the re-
mote room thermostat and select the desired mode using the arrow
buttons "↑ ↓". The following modes are available:
• PROGRAM 1: Manual program (heating and ventilation) (Fig. 5).
• PROGRAM 2: Automatic heating program (ECO heating) (Fig. 6).