Idiomas disponibles
Idiomas disponibles
Factory reset
1. Remove battery
2. Press and hold the ARM button
3. Insert batteries
4. Release button after flashes and tones stop
5. All detectors and remote controls have been removed
Frequently asked questions
Q: The Alarm unit does not give an alarm when a detector is activated
A1: Maybe the system is not armed yet. Short press the arm button【 】to switch
the Alarm unit on.Or press the arm button【 】on remote control to arm the device.
A2. Are the sensors active? The red light on the sensor should light up if the sensor
is activated.
A3. Maybe the batteries are running empty. In this case, replace the batteries.
A4. Sometimes the signal cannot penetrate concrete walls or cover large distances
between Alarm unit and the sensor. Take the Alarm unit and hold it close to the
sensor whilst activating it.This will show if the distance between the units is too high.
Q: The Alarm Unit does not enter pairing mode when pressing the digital
button [
,
, ,
].
A1: The device might be on arm mode. Try short pressing the arm button【
switch the unit disarm mode. Now, enter Pairing mode by long pressing the one of
four digital button [
,
, ,
].
A2: Check the batteries. They might be empty.
Q: The remote-control indicator light is on when I press a button but the Alarm unit
does not react to it.
A1: The signal might not penetrate thick concrete walls or cover large distances.
Try holding the remote control closer to check this.
A2: Try opening the remote control and taking the battery out- and back in again.
A3: The battery is running out of power. Insert a new battery.
Q: Where can I find more information and instructional video's?
A: Please visit www.cpvans.com for additional information.
Q: I want to add sensors like a window & door sensor or another PIR motion
detector. Where can I find these?
A: All our products are offered on Amazon CPVan Direct Storefront . You can also
visit www.cpvans.com for more information availability.
Q: I have a question and cannot find the answer in this manual
A: Just send your question to [email protected]. We respond usually within 24 hours.
BEDIENUNGSANLEITUNG (DE)
Contents
Einleitung.............................................................................................................2
Was ist im Hausalarm Starter Set enthalten? ..................................................3
Übersicht über das Hausalarm Starter Set.......................................................3
Alarmeinheit........................................................................................................3
Tür & Fenster Sensor.........................................................................................4
Fernbedienung................................................................................................... 4
Vorbereitung der Alarmeinheit..........................................................................5
Wie Sie die Einstellknöpfe richtig nutzen........................................................5
Wie Sie die Alarmeinheit nutzen.......................................................................5
Wie Sie die Fernbedienung nutzen...................................................................6
Installation des Tür & Fenster Sensors...........................................................6
Verbinden mit Sensoren und der Fernbedienung...........................................7
Verbinden einer Fernbedienung mit der Alarmeinheit....................................8
Entfernen von Fernbedienungen und Sensoren.............................................8
Entfernen einer Fernbedienung........................................................................8
】 to
Entfernen der Sensoren aus einer Zone..........................................................9
Den Code zurücksetzen.....................................................................................9
Umstellung der Lautstärke ................................................................................9
Austauschen der Batterien................................................................................9
Fernbedienung. Entfernen Sie nun die Abdeckung. Die Batterie ist nun
zugänglich and kann ausgetauscht werden. Der korrekte Batterie-Typ ist
CR2032 (3V, Lithium-Batterie)...........................................................................9
und ersetzen Sie die 2 x AAA (1,5V) Alkaline-Batterien.................................9
und ersetzen Sie die Lithium-Batterie Typ CR2450 (3V)................................9
Fernbedienungen ..............................................................................................9
Häufig gestellte Fragen und Antworten..........................................................10
Capítulos
