Entering The Pairing Mode; Using The Remote Control; Installation Of A Door Sensor; General Guidelines - CPVan CP3 Manual De Usuario

When a sensor is triggered:
The sound will be heard, Chime or Siren.
If the Siren is selected as a notification sound, the LED lights will indicate which
zone triggered the alarm (one of the four LEDs will light up).
If the Chime sound was selected as a notification sound, all 4 LEDs will light to
indicate a sensor was triggered but the zone will not be indicated.

Using the remote control

The supplied remote control will work with multiple Alarm units if required.
There are four buttons on the remote control:
Button Action
Bell Button Alarm will sound
Delay button 30 seconds delay Exit
Arm button Switch On
Disarm button Switch Off

Installation of a door sensor

GENERAL GUIDELINES:

•
Do not install the Door/Window sensors on breakable material, but choose instead
the frame of a window to attach your Door/Window sensor.
•
Do not install on instable parts.
•
Do not install the sensor near magnetic parts that might trigger the alarm by accident.
•
Clean the surface before installation if the tape will be used for attachment.
•
It is important that the sensor and the magnet are placed on the door and frame
respectively to allow an alarm to be triggered when sensor and magnet are separated.

Pairing with sensors and remote control

The Alarm unit is already paired with the remote control and the door sensors. Use
this procedure to connect more door & window detectors from the CPVan Home
Alarm System.
IMPORTANT: Factory setup: The visual indicator on the front of the Alarm unit has
What happens if pressed
Siren sounds loud. Press Disarm button to stop
Alarm unit is activated after 30 seconds
Alarm unit is activated
Alarm unit is deactivated
4 digital LED's which can be used to see which zone is activated in Siren mode (but
not in Chime mode). Please note that one door sensor has been paired with Zone 1
and the other door sensor has been paired to Zone 2 out of the factory as a standard.
This will get you started quickly.
IMPORTANT: In the procedure below you will need to activate sensors to pair them
with the Alarm unit. A door sensor can be activated by keeping the sensor and magnet
against each other and then move them away from each other. A PIR sensor can be
activated by waving your hand in front of it or press the light which showing below
the CPVan.
Entering pairing mode
•
Long press the one of four digital button on the Alarm unit to enter pairing mode.
The respective light on the front will light up.
Setup Zone 1
•
Make sure the Alarm unit is On.
•
Long press the digital button [ ] once to select Zone 1. The relevant [
now lit.
•
Activate the respective unit (door sensor or PIR) which corresponds to Zone 1.
Two beeps will be heard. The sensor for Zone 1 is now properly connected.
Meantime,the light will be off and exit the pairing mode. Other sensors can be
connected for this zone by activating it at last stage.
Setup Zones 2-4
•
Long press the digital button [ ] to select the zone 2.The relevant [
•
Activate the respective units (door sensor or PIR) which correspond to Zone 2.
Two beeps will be heard. The sensor for Zone 2 is now properly connected.
Meantime,the light will be off and exit the pairing mode. Other sensors can be
connected for this zone by activating it at last stage.
•
Long press the one of digital button [ ,
described to add further sensors, The respective zone is now properly connected, the
light will be off and exit the pairing mode.
Pairing with remote control
Your remote control is ready for use and already paired with your Alarm unit but you
can add more remote controls if desired.
1. Enter the pairing mode by long pressing the arm button [
2. Press the arm or disarm button on your remote once. Two beeps will be heard as
a confirmation, all red lights will be off and exit the pairing mode.
] light is
] light is now lit.
] to select Zone 3 or Zone 4 and do as
]. All red lights are now lit.