General Indications - Miche SYNTIUM DX Manual De Uso

eNgLisH

geNerAL iNdicATiONs

1
We thank you for buying the SYNTIUM DX wheels, product that will
guarantee you security and functionality through the years.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing. Fac Michelin S.r.l. reserve to modify the content of this
manual without notice. The updated version will always be avai-
lable www.miche.it
On our website you will also find information on the other Miche or
SWR products and the spare parts catalogue.
In the box of wheel set you will find:
• The front wheel arranged with TX-12 system
• The rear wheel arranged with TX-12 system
• The manual of instructions and use of wheels
• Rim tapes
Warning
!
Any modification or alteration (and graphic) of the product with
non-original spare parts or spare parts not delivered directly
by Fac Michelin S.r.l., involves the expiration of the guarantee.
Warning
!
Direct and violent impacts on broken road surfaces can cause
damage to the rims. Such damage is outside the conditions of
our guarantee and repair costs will be charged directly to the
customer.
Warning
!
In case of strange impact caused from bad road base or wheels
transport, we trust to bring the wheels to your mechanic for a
check.
Warning
!
Only Shimano original lock ring designed for through axle inter-
nal diameter 27mm to be used with the disc brake.
Warning before using the bicycle:
• Check for proper operation and state of wear of all the compo- nents before starting to ride.
• Check the condition and pressure of the tyres fitted to your Mi-
che wheels.
• Check that the wheels are firmly anchored to the frame with
the locking item closed in the correct position (Fig. 7-8). If there is the passing through pin, consult the installation instructions
provided by the manufacturer of the bicycle or fork.
Attention, an incorrect locking may cause the detachment of the
wheel and derive in accidents and serious or fatal injuries.
• Check the tension of the spokes so as to notice any spokes
which got loose. In the case spokes are loose, contact a qua-
lified mechanic or special personnel to perform the tensioning.
Attention, the use of wheels not centered properly or with spokes
broken and/or loosen or damaged may cause an accident, serious
injury or death.
• Check that the braking system and the brake pads in the brake
calipers are in good state and that the screws on the disc or the
locking ring of the disc, depending on your model, are properly
locked.
• To the users of more than 85kg weight, Fac Michelin S.r.l. sug-
gests to check the wheels status to the mechanic every two
months or every 1,500km.
• We reccomend using these wheels if you weigh more than
102 Kg
• Never wash the pieces with pressure-fed water because water
may get through the seals and cause permanent damage to the
internal components. We recommend washing components with
a sponge, mild soap, and water.
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Care-
fully rinse, clean, dry and re-lubricate all exposed parts to avoid
damage, malfunctions and accidents.
• If your component shows signs of rust, this means it has to
be changed urgently as it might be a sign of damage.
HuBs
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side 26x17x5 (6803)
Left side 26x17x5 (6803)
The SYNTIUM DX hubs are easy to maintain. To do it, proceed as
follows:
frONT HuB The front hub does not require any particular maintenance. For any
extraordinary maintenance and replacement of bearings, follow
these simple steps.
• Extract the cage chamber (B) including the nuts (Fig. 1)
Once the chamber successfully removed proceed replacing the
bearings.
• Apply light pressure to the axel (C) using a plastic-edged tool:
apply pressure until the bearing has been totally removed from
its housing including the axel (Pic. 2)
Once the first bearing has been removed, using special 17mm dia-
meter extractor, you can then remove the second bearing (Pic. 2).
Once these have been replaced, proceed in fitting the new bea-
rings:
Front hub
26x17x5 (6803)
26x17x5 (6803)
5