General Description; Description Of Controls - Elettro CF PRO MIG 466 PULSED Manual De Instrucciones

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
INSTRUCTION MANUAL FOR WIRE WELDING MACHINE
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES MANUAL
CAREFULLY BEFORE INSTALLING, USING, OR SERVICING
THE WELDING MACHINE, PAYING SPECIAL ATTENTION TO
SAFETY RULES. CONTACT YOUR DISTRIBUTOR IF YOU DO
NOT FULLY UNDERSTAND THESE INSTRUCTIONS.
This machine must be used for welding only. It must not be used
to defrost pipes.
It is also essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must be
stored carefully in a pica familiar to everyone involved in using
the machine. They must be consulted whenever doubts arise
and be kept for the entire lifespan of the machine; they will also
be used for ordering replacement parts.

1. GENERAL DESCRIPTION

1.1. SPECIFICATIONS
This manual has been prepared for the purpose of educating
personnel assigned to install, operate and service the welding
machine.
This equipment is a constant-voltage power source, suitable for
pulsed synergic MIG/MAG
MIG/MAG, conventional MIG/MAG, TIG (DC) with scratch
starting of the arc and MMA, developed using inverter
technology.
Upon receiving the machine, make sure there are no broken or
damaged parts. The purchaser should address any complaints
for losses or damage to the vector. Please indicate the article
and serial number whenever requesting information about the
welding machine.
1.2. EXPLANATION OF TECHNICAL SPECIFICATIONS
The welding machine is manufactured
according to these international standards.
Three-phase static frequency converter
transformer-rectifier
Suitable for MIG welding.
Suitable for welding with covered electrodes.
Suitable for TIG welding.
U0
Secondary open-circuit voltage.
X
Duty cycle percentage.
The duty cycle expresses the percentage of 10
minutes during which the welding machine may
run at a certain current without overheating.
I
Welding current
2
welding, non-pulsed synergic
Pict. 1
U
Secondary voltage with welding current I2.
2
U
Rated supply voltage
1
3~ 50/60Hz 50- or 60-Hz three-phase power supply.
I
max
Max. absorbed current at the corresponding
1
current I
I
eff
This is the maximum value of the actual current
1
absorbed, considering the duty cycle. This value
usually corresponds to the capacity of the fuse
(delayed type) to be used as a protection for the
equipment.
IP 23
Protection rating for the housing. Grade 3 as the
second digit means that this equipment is suitable
for use outdoors in the rain.
Suitable for use in high-risk environments.
NOTES: The welding machine has also been designed for use
in environments with a pollution rating of 3. (See IEC 60664).
2. INSTALLATION
• Only skilled personnel should install the machine.
• All connections must be carried out according to current
regulations, and in full observance of safety laws.
Make sure that the supply voltage corresponds to the value
indicated on the power cable. If it is not already fitted, connect a
plug suited to the power cable, making sure that the
yellow/green conductor is connected to the earth pin.
The capacity of the overload cutout switch or fuses installed in
series with the power supply must be equivalent to the absorbed
current I1 max. of the machine.
2.1. PLACEMENT
Place the welding machine in a ventilated area.
Dust, dirt, and any other foreign matter entering the welding
machine can interfere with ventilation and thus with smooth
operation.
Therefore, in relation to the environment and working conditions,
it is important to keep the internal parts clean. Clean using a jet
of dry, clean air, being careful to avoid damaging the machine in
any way. Before working inside the welding machine, make sure
it is unplugged from the power mains.
Any intervention carried out inside the welding machine
must be performed by qualified personnel.
2.2. LIFTING
See picture A page 2.
2.3. ASSEMBLY
See pictures B, C, D and E page 3.
2.4. ASSEMBLY OF THE EXTENSION PROTECTION
See picture F and G page 4.

3. DESCRIPTION OF CONTROLS

3.1. DESCRIPTION OF POWER SOURCE (see pict. 2 page 5)
E - Connector:
Connector type DB9 (RS 232) to be used to update the
microprocessor programs.
F - Socket:
In MIG welding, connect the earth cable connector. For TIG
welding, connect the power DINSE of the power source/wire
feeder connection cable, using the extension for TIG welding
code 530347.
L - Switch ON/OFF.
M - Power input cable.
14
and voltage U
.
2
2
Tabla de contenido
loading

Este manual también es adecuado para:

Pro mig 566 pulsed

Tabla de contenido