Battery Charging; Changing The Tool; Dust/Chip Extraction - Bosch AdvancedDrill 18 Manual Original

Fitting

Battery charging

Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Removing the battery
To remove the battery , press the battery release button and
pull the battery to the rear and out of the power tool. Do not
use force to do this.
Battery charge indicator
When the on/off switch (14) is pressed in halfway or com-
pletely, the battery charge-control indicator (13) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slowly flashing light 1 x green
The three LEDs in the battery charge indicator flash
quickly when the temperature of the battery is outside
the operating temperature range of –30 to +65 °C and/or
the overload protection has been triggered.

Changing the Tool

Inserting the application tool (see figure A)
Insert the application tool all the way into the tool holder (2).
The application tool is held in the tool holder by means of a
magnet.
Bosch Power Tools
Removing
Remove the application tool from the tool holder (2).
Fitting the adapter (see figure B)
Remove the application tool.
Insert the adapter into the tool holder (2). The adapter clicks
audibly into place.
Check that it is seated securely by pulling the adapter.
Inserting the application tool into the adapter (see figure
C)
Insert the application tool all the way into the adapter. The
application tool is held in the adapter by means of a magnet.
Screw holder (see figure D)
The screw holder (16) stabilises the screws so that they can
be better positioned on the workpiece.
Remove the application tool.
Push the screw holder onto the tool holder (2) until it aud-
ibly engages. Push the magnetic cap (15) as far as it will go
towards the power tool.
Then push the screwdriver bit (20) onto the screw holder
(16) and pull the magnetic cap forwards over the screw-
driver bit.
Push a screw onto the screwdriver bit.
Drill chuck adapter (see figure E)
Open the drill chuck adapter (18) by turning it in the direc-
tion of rotation ➊ until the application tool can be inserted.
Insert the application tool.
Firmly tighten the sleeve of the drill chuck adapter (18) by
turning it by hand in the direction of rotation ➋. This will
automatically lock the drill chuck.
Turning the adapter (see figure F)
Pull the unlocking ring (1) away from the power tool and
then pull the adapter off the tool holder (2).
Turn the adapter to the required position and then reattach
it.
Check that it is seated securely by pulling the adapter.
Removing the adapter (see figure G)
Capacity
Remove the application tool.
≥ 66%
Pull the unlocking ring (1) away from the power tool and
33–66%
then pull the adapter off the tool holder (2).
11–33%
Combining adapters (see figure H)
≤ 10%
Remove the application tool.
Push the angle screw adapter (17) onto the tool holder (2).
Check that it is seated securely by pulling the angle screw
adapter (17).
Push the drill chuck adapter (18) onto the angle screw ad-
apter (17).
Check that it is seated securely by pulling the drill chuck ad-
apter (18).

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
English | 19
1 609 92A 4BE | (07.09.2018)