HIKOKI D 6SH Instrucciones De Manejo página 6

English
DRILL SAFETY WARNINGS
1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
4. When mounting the drill bit, insert it fully into the
drill chuck and completely tighten the drill chuck
with the chuck wrench.
SPECIFICATIONS
Model
Voltage (by areas)*
Power input
No-load speed
Capacity: steel
wood
Weight (without cord)
Spec. for keyed chuck
Spec. for keyless chuck
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Chuck Wrench (Spec. only for keyed chuck) ...... 1
(2) Stopper Ass'y (Spec. only for keyed chuck) ....... 1
(3) Hook ............................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATION
Drilling holes into various metals, lumbers and
plastics.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting the drill bit
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn. (Fig. 3)
5
If mounting is not done porperly, it is very dangerous
as the drill bit may slip or loosen during operation.
5. Do not wear gloves made of stuff liable to roll up
such as cotton, wool, cloth or string, etc.
6. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
7. When placing the drill on the floor, make sure that
the drill has stopped completely.
8. Before drilling into a wall, floor or ceiling, thoroughly
confirm that no items such as electric cables or
conduits are buried inside.
9. When working in high position, take care of
downword direction.
D6SH
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
240 W*
–1
4500 min
6.5 mm
9 mm
0.9 kg
1.0 kg
For keyless chuck
(1) Mounting the bit
After inserting a drill bit, etc. into the keyless drill
chuck, firmly grasp the ring and tighten the sleeve
by turning it toward the right (in the clockwise
direction as viewed from the front).
If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by
turning it toward the left (in the counter-clockwise
direction as viewed from the front)
5. Selecting the appropriate drill bit
(1) When drilling holes in metals or plastics:
Use ordinary metalworking drill bits;
Applicable drill sizes range from 0.5 mm min. to
6.5 mm max.
(2) When drilling holes in lumber:
Use woodworking drill bits.
For small holes of 6.5 mm dia, or less, use
metalworking drill bits.
6. RCD
The use of a residual current device with a rated
residual current of 30mA or less at all times is
recommended.
PRACTICAL HANDLING PROCEDURES
1. Pressure:
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result
in a damaged drill bit, decreased drilling efficiency
and/or shortened service life of the drill.
D6SB
–1
3000 min
6.5 mm
13 mm
(Fig. 4)