Standard Accessories; Optional Accessory - HIKOKI N 5008AC2 Instrucciones De Manejo

STAPLE SELECTION
Choose a suitable staple from Fig. Staples which are not
shown in Fig. can not be driven with this tool.
16 Gauge 7/16" Crown
Min.
1.45 mm
7.9 mm
(.057")
(.309")
Dimension of staples

STANDARD ACCESSORIES

(1) Hexagon bar wrench for M5 screw .............................. 1
(2) Eye protection .............................................................. 1
(3) Oiler .............................................................................. 1

OPTIONAL ACCESSORY

○ Sequential Trip Mechanism Kit (Code No.876762)
(Sequential Fire Parts Set, Single Shot Parts)
With the sequential fi re parts, the staple is driven only
by squeezing the trigger after pushing down the push
lever.
By installing these parts, driving staples into improper
positions and unexpected fi ring of staples caused
by accidental operation of the push lever can be
prevented.
APPLICATIONS
○ Construction work such as wall sheathing, subfl ooring.
○ Mobile and modular home construction.
PREPARATION PRIOR TO OPERATION
1. Prepare the hose
Be sure to use the hose provided with minimum 6 mm
(1/4") inside diameter.
NOTE
The air supply hoses must have a minimum working
pressure rating of 12.8 bar (180 psi) or 150 percent
of the maximum pressure produced in the air supply
system, whichever is higher.
2. Check on safety
CAUTION
○ Unauthorized persons (including children) must be kept
away from the equipment.
○ Wear eye protection.
○ Check the retaining screws which fi x the exhaust cover,
etc. for tightness.
Check the stapler for air leaks and defective or rusty
parts.
○ Check whether or not the push lever works correctly.
Also check whether or not any dirt has adhered to the
moving parts of the push lever.
○ Recheck on operational safety.
BEFORE USE
1. Check the air pressure
Max.
CAUTION
The air pressure must be constantly maintained at
4.9 – 8.3 bar (70 – 120 psi).
Adjust the air pressure between 4.9 to 8.3 bar (70 – 120
psi) according to the diameters and length of staples
and hardness of the wood being stapled. Pay special
attention to the output pressure, capacity, and piping
on the air compressor, so that air pressure does not
exceed the specifi ed limit. Note that excessive pressure
may aff ect overall performance, service life, and safety.
2. Lubrication
(1) Prior to operating this stapler, be sure to provide an
air set between the air compressor and this device.
Lubrication through the air set off ers smooth operation,
extended service life, and anticorrosion.
Adjust the oiler so that a single drop of oil is supplied at
intervals of 5 to 10 stapling cycles.
(2) It is recommended using the recommended oil (SHELL
TONNA). Other applicable oils are listed. Never mix two
or more types of diff erent oils.
3. Load staples
CAUTION
○ When loading staples into stapler,
(1) do not depress trigger;
(2) do not depress push lever; and
(3) keep your face, hands feet and other body parts, as well
(1) Pull the staple feeder backward and attach it securely
to a groove of the magazine. (See Fig. 2)
(2) Place the staple strip over the magazine.
Make sure that the staple strip slides freely on the
magazine. (See Fig. 3)
(3) Pull the staple feeder backward. Then, detach it from
the groove of magazine and softly bring the staple back
as if it were being gently pushed, avoiding any impact.
(See Fig. 4)
The stapler is now ready to operate.
CAUTION
○ If the staple feeder is released all of a sudden, it can
return abruptly, causing deformation and/or scatter,
eventually ending up in clogged staples.
Be absolutely sure to bring back the staple feeder,
avoiding any impact.
○ To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a work
bench on fl oor. Also, never face the staple outlet toward
any part of a person.
HOW TO USE THE STAPLER
CAUTION
○ Do not use the body or any portion of the tool as a
hammer as staples may be discharged unexpectedly or
the tool may become damaged and serious injury could
occur.
○ Take precautions to ensure the safety of persons in
the vicinity during operation.
○ Ensure tool is always safely engaged on the workpiece
and cannot slip.
○ Never carry a pneumatic tool by its hose.
○ Never drag a pneumatic tool by its hose.
as those of other persons away from the nose muzzle to
avoid possible injury during usage and carrying.
English
9