Maintenance And Storage; Notes; Warnings - IKRA IEVL 1738 Instrucciones De Manejo

d) Move the tool at walking speed only.
e) Always work in a perpendicular position/di-
rection to the slope. Never work in upward or
downward direction!
f) Take particular care when changing the work-
ing direction on the slope.
g) Do not work on extremely steep slopes.
h) Take particular care when turning the tool
around or pulling it towards yourself.
i) Stop the work tools if the tool must be tilted for
transport purposes. Stop the work tools if are-
as other than grass patches must be crossed
and whenever the tool is moved to and from
the area to be worked.
j) Do not use the tool with damaged or no safety
devices installed, e.g., without baffle plates
and/or collection devices.
k) Do not change the motor settings and do not
overrev the motor.
l) Disengage ('declutch') all work tools and
drives prior to starting the motor.
m) Start the tool with due care in accordance with
the manufacturer's instructions. Make sure to
keep a safe distance between your feet and
the the work tools.
n) The tool must never be tilted when starting
the motor unless the tool must be lifted off the
ground to be started. If this should be the case
only tilt the tool as far as necessary and only
lift the side pointing away from the operator
off the ground.
o) Do not start the motor while standing in front
of the ejection chute.
p) Never reach under or touch rotating parts with
your hands or feet. Keep away from the ejec-
tion opening.
q) Never lift or carry a tool with the motor running.
r) Switch off the motor and pull the mains plug in
the following cases:
- before removing blockages or obstructions
in the ejection chute.
- before inspecting or cleaning the tool or be-
fore performing any works on it.
- if an object got caught or hit. Check the tool
for damages and perform the required re-
pairs before you restart and continue work-
ing with the tool.
- if the tool starts to vibrate abnormally (in-
spect immediately!).
s) Switch off the motor and pull the mains plug
whenever you leave the tool alone.
GB | Operating Instructions

Maintenance and storage

a) Make sure that all nuts, bolts and screws are
c) Let the engine cool down before you store the
e) Regularly check the collecting device for signs
f) Inspect the tool regularly and replace worn-
Safety instructions for Electric Lawn Scarifier
& Raker

Notes

a) Check the mains and extensions cables for
b) Pull the mains plug in case the cable gets
c) Visually inspect the cutting unit for signs of
d) Do not unnecessarily tilt the device when
e) Safety devices must be replaced by our after-

Warnings

a) Warning! The device is not intended for use
b) Do not use the lawn scarifier & raker if the ca-
c) Do not connect a damaged cable to the mains
d) Do not touch the tines unless the device's
e) Keep extension cords away from the tines. A
GB-3
firmly tightened to ensure the tool's safe work-
ing condition.
tool in a closed room.
of wear and tear or damaged parts.
out or damaged parts for reasons of safety.
signs of damage or ageing before use. Do not
use a device with defective cables.
damaged during use. Do not touch the cable
under any circumstances!
wear and tear or damages each time before
you start using the device. If the device starts
to vibrate abnormally it is required to inspect
it immediately!
starting the motor. Only tilt the device as far as
necessary and only lift the side pointing away
from the operator off the ground. Make sure
to hold the device with both hands in working
position before you put it back on the ground.
sales service only.
by children.
bles are damaged or worn.
supply and do not touch a damaged cable as
long as it is connected to the mains supply. A
damaged cable may lead to the contact with
active parts.
power supply has been disconnected and the
tines fully stopped moving.
damaged cable may come into contact with
active parts (hazard of electric shock).