Instructions For Use; Placement Tool; Assembly - stayer CPT3000E Manual De Instrucciones

bring the blade in line with your body. In a kickback, the
saw can jump backwards, but the operator can control
the kickback forces if appropriate measures were
taken.
- If the saw blade jams or sawing is interrupted for any
reason, release the ON / OFF switch and calmly hold
the saw in the material until the saw blade stands
completely still. Never attempt to remove the saw from
the workpiece or pull it backwards as long as the saw
blade is moving or a kickback might occur. Find the
cause of the saw blade jam and eliminate them through
appropriate measures.
- When you want to restart a saw that is stuck in a
workpiece, center the saw blade in the saw gap
and check that the saw teeth are not stuck in the
workpiece. If the saw blade jams, it can move out from
the workpiece or a kickback can happen if the saw is
restarted.
- Prop up large panels in order to minimise the risk of a
kickback by a jammed saw blade. Large panels tend to
sag under their own weight. Panels must be supported
on both sides, both in the vicinity of the saw gap as well
as on the edge.
- Do not use dull or damaged saw blades. Saw blades
with blunt or misaligned teeth cause increased
friction, jamming of the saw blade and kickback by an
excessively narrow saw gap.
- Tighten the cutting depth position prior to cutting. If the
settings change while cutting, the saw blade can jam
and a kickback can occur.
- Be especially careful if you perform a "circular cut" in a
hidden area, such as an existing wall. The protruding
saw blade can get blocked in hidden objects while
cutting and cause a kickback.
- Do not place the saw on the workbench or the floor
unless the saw blade is at a standstill. An unprotected,
running saw blade moves the saw against the cutting
direction and cuts whatever is in its way. Thus note the
delay time of the saw.
- For this reason, the saw is not suitable for use in
reverse position as fixed equipment.
TABLE SAFETY ICONS
Denotes risk of personal injury or damage to the tool.
Lea este manual
antes de utilizar
el aparato.
In accordance
with essential
requirements of the
European directive(s)
"Class II - The machine is double insulated; Earthing
wire is therefore not necessary.
- Do not operate the saw if it is not working properly or
has been damaged. In case of technical problems, do
not attempt to repair it on your own. Contact the service
or have the saw repaired by a professional.
ENGLISH
21
3.

Instructions for use

3.1 Placement tool

Carefully remove the tool and all loose items from the
shipping container.
Retain all packing materials until after you have inspected
and satisfactorily operated the machine.

3.2 Assembly

- Before each use check the proper function of all
installation fixtures of the plunge saw and only use the
plunge saw if everything works properly.
- Attach the work piece in such way that it cannot move
or bend during work. Line the work piece respectively.
- Always hold the plunge saw with both hands at the
hand grips (3) and (4).
- Always guide the plunge saw forward. Never draw the
plunge saw back!
- Place the plunge saw with the front part of the base
plate (5) on the work piece. Guide the plunge saw only
against the work piece during operation.
- With the correct forward speed you prevent overheating
of the saw blade, and melting when cutting plastics.
Plunge saw feature
Selector switch
Use the selector switch (17) to set the respective operation
mode.
Always wear
protective gloves
Guide rails and clamps (Fig. 1)
Always wear safety
goggles.
Fixing with the clamps ensures solid grip and safe work.
- Place the guide rail on the work piece and fix the guide
rail with the clamps. Slide the bar into the groove of the
guide rail and tighten the clamp with the lever.
- Place the plunge saw on the guide rail. The base plate
has a groove (13), which exactly fits into the guide
ridge of the rail.
21
Before setting up, repair or maintenance of
the appliance you must always turn off the
operating switch and pull out the mains plug!
Corte de Corte de
inmersión marcado
Cambio de hoja
de sierra