Weekly Maintenance; Rear Squeegee Rubber Check; Squeegee "V" Type (Optional); Squeegee "V" Type (Optional): Rear Rubber Replacement - ADIATEK sapphire 70s Manual Del Usuario

GB
2. Disassemble the squeegee (2) from its support (1)
by loosening the knobs (4) counterclockwise and
making slide the threaded parts in the appropriate
slots up to their release.
3. Clean with care the internal part of the squeegee
inlet eliminating eventual dirt residuals.
4. Clean with care the squeegee rubbers.
5. Reassemble all parts paying attention to put the
washers (3) into position, they are two for each knob,
so that they are assembled one under and the other
on each of the two slots present on the support.

WEEKLY MAINTENANCE

REAR SQUEEGEE RUBBER CHECK

Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee (see under paragraph "STOP OF
THE MACHINE AFTER CLEANING OPERATION").
2. Release the hook (1) of the rubber holder blade
and take off the rubber.
3. Turn the rubber to a new side or replace it.
To reassemble the squeegee repeat inversely the op-
erations mentioned above, inserting the rubber on
the guides and blocking it with the rubber holder
blade.

SQUEEGEE "V" TYPE (OPTIONAL)

Alternatively to the standard squeegee, a "V"-shaped
squeegee is available, especially indicated for floors
with large joints.
This squeegee is interchangeable with the standard
one, same assembly on the machine, same adjust-
ment in height, pressure and inclination.
Different though are the methods in assembly and
disassembly of the squeegee rubbers.
SQUEEGEE "V" TYPE (OPTIONAL): REAR RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee (see under paragraph "STOP OF
THE MACHINE AFTER CLEANING OPERATION").
2. Unscrew the tie rods (1) on the terminals (2) of
the rubber holder blade and disengage the terminals.
3. Unscrew the wing nuts (3) and take off the rub-
ber holder blade (4).
4. Turn the rubber (5) to a new side or replace it.
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting first the rubber (5)
into its guides, then positioning the rubber holder
blade and finally screwing down all wing nuts and
the tie rods of the two terminals.

CHECK OF THE SIDE RUBBERS

With the brushes assembled, the side rubbers must
touch the floor. If they are worn, they have to be re-
placed.
To replace the rubbers on both sides of the machine:
1. Unblock the bar of the side rubber after having
released the knob (1).
2. Open the bar of the side rubber (2) as shown in
the figure.
3. Take off the fixing screws (3) of the rubber blade
(4) and replace the rubber.
4. Reassemble all parts.
28

SQUEEGEE HOSE CLEANING

Weekly or in case of insufficient suction, it is neces-
sary to check that the squeegee hose is not obstruct-
ed. Eventually, to clean it, proceed as follows:
1. Take off the hose (1) from the squeegee coupling.
2. Wash the inside of the hose with a water jet.
3. To reassemble the hose repeat inversely the
above-mentioned operations.
CLEANING OF THE SOLUTION TANK AND OF THE
OUTER FILTER
1. Bring the machine to an appropriate place for
the detergent solution draining.
2. Unscrew the solution tank cap (1).
3. Unscrew the cap of the exhaust filter (2) and
take off the filter. Be careful not to lose the gasket
of the cap.
4. Open the solution valve (see under paragraph
"FLOW ADJUSTMENT OF THE DETERGENT SOLUTION"),
so that the detergent solution flows down into ap-
propriate containers.
5. Rinse with a water jet the solution tank and the
components of the filter.
6. Reassemble all parts.
NOTE: in case of need it is possible to wash only the
components of the outer solution filter as above-
mentioned by closing the solution valve adjustment
(see under paragraph "FLOW ADJUSTMENT OF THE
DETERGENT SOLUTION"), so that the detergent solu-
tion remains in the solution tank.

TWO-MONTHLY MAINTENANCE

FRONT SQUEEGEE RUBBER CHECK

Check the wear of the squeegee rubber and eventu-
ally replace it.
For the replacement it is necessary to:
1. Take off the squeegee (see under paragraph
"SQUEEGEE CLEANING").
2. Unscrew the wing nuts in the front part of the
squeegee.
3. Take off the rubber holder blade.
4. Replace the front rubber.
5. Reassemble all parts.
SQUEEGEE "V" TYPE (OPTIONAL): FRONT RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually re-
place it.
GB