Daily Maintenance; Recovery Tank Emptying And Cleaning; Emptying And Cleaning Of The Collection Box; Suction Filter Cleaning - ADIATEK sapphire 70s Manual Del Usuario

GB
phase of the brushes" and furthermore can dry the
suction hose of its dirty water.
At any time it is possible to interrupt the proce-
dure BREAK WASHING by stopping the drive.
2. During the phase of BREAK WASHING, when the
accelerator pedal is released for more than 3 seconds,
the squeegee raises itself and the suction switches
off automatically.
3. After three seconds, the accelerator can be
pressed again, if a machine's transfer has to be made
(you can anyway make the transfer even if the pedal
is not lifted once that 20 seconds have passed).
4. Turn the switch key counterclockwise to switch
off the machine.
5. Insert the parking brake (see under paragraph
"EMERGENCY-PARKING BRAKE").
ATTENTION:
The mode (BREAK WASHING) is specific for the
transfer at the end of the cleaning operation.
Starting again the cleaning operation:
A. by pressing the push button (6) the automatic
(AUTO) functioning is chosen to start working in au-
tomatic mode.
B. by pressing the push button (3) the manual (MAN)
functioning is chosen to start working in manual
mode and all functions have to be re-established
manually.

DAILY MAINTENANCE

ATTENTION:
All the following maintenance and cleaning opera-
tions that refer to the following components that
are in contact with liquids and therefore:
• Solution and recovery tanks
• collection box
• Solution and recovery filters
• Squeegee with their rubbers and hoses
• Brushes
must be carried out using gloves to protect from
contact with dangerous solutions.

RECOVERY TANK EMPTYING AND CLEANING

1. Hold the exhaust hose (1) placed in the rear low
part of the machine after having taken it off from its
fixing support.
2. Take off the plug (2) from the exhaust hose act-
ing upon its lever (3) and empty the recovery tank
into appropriate containers, in compliance with the
respective rules what the liquid disposal concerns.
3. Take off suction cover (4) after rotating the
blocking levers (5).
4. Take off the filter and filter protection (6).
5. Rinse the inside of the tank with a water jet
through the hole become free of the filter, paying
attention to clean the eventual float switch (7) (op-
tional) and its protection placed right under the hole.
6. Reassemble all parts.
EMPTYING AND CLEANING OF THE COLLECTION
BOX
The machine is equipped with a collection box for
the solid dirt.
At the end of the cleaning operation it is necessary
to empty and to clean it with a water jet.
For the emptying and the cleaning of the box:
1. Position the selector (10) for the adjustment of
the brushes pressure on position P1.
2. Activate the machine (see under paragraph
"STARTING OF THE MACHINE") positioning the selec-
tor (3) to the right to choose the manual mode
(MAN).
3. Activate the push button (17) of up/down of the
brushes base to lower the brushes. Once it is lowered,
the brushes begin to turn.
4. Turn the key counterclockwise to turn off the
machine.
ATTENTION:
To carry out above operations with the electric sup-
ply on, may cause damages to hands.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.
5. Unblock the bar of the side rubber after having
released the knob (1).
27
6. Open the bar of the side rubber (2) as shown in
the figure.
7. Extract and carry the box by using its handles (3).
8. Empty the box into appropriate containers, in
compliance with the respective rules what the liquid
disposal concerns.
9. Put the collection box back into its position up to
the end seat.
10. Place the bar of the side rubber (2) into its posi-
tion blocking it with the knob (1).

SUCTION FILTER CLEANING

1. Take off suction cover (4) after rotating the
blocking levers (5).
2. Take off the filter (8) and its filter protection (6).
3. Clean all parts with a water jet and especially the
inside surfaces and the filter bottom.
4. Carry out cleaning operations carefully.
5. Reassemble all parts.

BRUSHES CLEANING

Disassemble the brushes and clean them with a wa-
ter jet (for the brushes disassembly see under para-
graph "BRUSHES ASSEMBLY AND DISASSEMBLY").
ATTENTION:
To carry out brushes disassembly operations with the
electric supply on, may cause damages to hands.

SQUEEGEE CLEANING

Keeping the squeegee clean guarantees always the
best drying result.
For its cleaning it is necessary to:
1. Take off the squeegee hose (5) from the coupling.
GB