Machine Drive; Vehicle Operation - Active ELECTRO POWER TRACK 1460 Manual De Instrucciones

22-The brake is engaged when the lever (10) is
disengaged. On the slopes, uneven terrain and when
travelling at high speed, pay attention to braking or
swerving as they can to overturn the vehicle or cau-
se loads to drop.
23- Park the vehicle on level, secure ground. Avoid
dangerous locations.
ATTENTION: carefully read the safety regulations.
If you are new to use of the vehicle, first carry out
a period of training.
- Always inspect the vehicle thoroughly before use. Make
sure there are no loose screws, damaged parts and oil
leaks.
- Check that the controls are working properly.
STARTING THE MOTOR
1- Make sure the accelerator lever (4) is at "minimum"
position.
2- Make sure the red drive lever (10) is in position A
"NEUTRLA" and, therefore, disengaged.
3- Select the gear lever on the mechanical gearbox (2):
1 forward —> to go up very fast
2-3 forward —> for all other cases
4- Check the position of forward/reverse drive switch (7) :
select forward (or reverse).
1- The machine is equipped with a built-in battery charger
(20) fig.6. Therefore, it is advisable to charge batteries (18)
fig.5 when the machine is not in use, in order to always
have the longest battery operation. The battery charger
must be powered at 220 and have a consumption of 300
W/h. It is also possible to use a 300 W inverter to connect
to the electrical system of a car or truck.
2- Connect the plug (13) to a 220 volt outlet
3- During charging, an orange light will switch on and when
charging is completed, a green light will switch on inside
the battery charger indicator (12)
4- The machine is equipped with a light (5). Always
remember to switch off when not in use. The operating
time range depends on the type of use, the type of path
being taken and the weight on the hopper.
5- Choose an appropriate speed to use when using the
gear lever (2) fig. 1.
ATTENTION: It is difficult to engage a gear, do not force it
but engage and then disengage the red drive lever (10)
until the gear engages smoothly. Make sure the gear has
been properly engaged.
ATTENTION: If you turn the key (11) to OFF and the
accelerator lever does not go into MINIMUM position, the
next time you turn the key(11) to ON, the machine, even
with the red lever (10) pressed, will not go drive.
Therefore, release the red lever (10) and bring the
accelerator lever (4) to MINIMUM.

5. MACHINE DRIVE

(Fig. 1 - 2)

6. VEHICLE OPERATION

19
24- When parking:
- on sloping terrain, use wedges to block the stopped
vehicle.
- release the clutch lever and stop the motor.
5- Turn the key (11) to the ON position
6- Press the drive lever (10)
7- Slowly turn the accelerator lever (4)
8- The machine will begin to move and the accelerator (4)
allows you to select the desired speed.
9- To reverse direction, set the switch(7) to the reverse
position.
10- In case of danger, quickly release the drive lever (10):
you will stop quickly in this way.
11- Any time the machine is to remain stopped, rotate the
key (11) to the OFF position: you can avoid unnecessary
battery drainage in this way.
STOPPING THE MOTOR
1- Release the drive lever (10) to disengage the
transmission.
2- Position the gear lever (2) to the "N" neutral position.
3- Bring the accelerator lever (4) to minimum.
4- Turn the key (11) to the OFF position.
Then press the red lever (10) and accelerate using the
lever (4) : the machine will begin to drive.
(This is a safety feature to prevent accidental forward drive
at full speed without the voluntary act of the operator).
6- To stop the vehicle, quickly release the red lever (10).
ATTENTION: use the vehicle in first gear (slow) on uneven
terrain. Do not change gears during drive.
Avoid U-turns and changing speed ratios.
7- To adjust the forward speed, slowly move the accelerator
lever (4).
CHANGING DIRECTION
- Pull the right or left lever on the lateral clutches (15) to
steer in the desired direction.
RIGHT LEVER: the vehicle turns right
LEFT LEVER: the vehicle turns left
If the levers are pulled at the same time, the vehicle will
immediately shut down.
"RIGHT" and "LEFT" refer to the operator in driving
position, gripping the handlebar.
REVERSE: before reversing, ensure that the area behind
you is clear of obstacles and that you can proceed with
maximum safety
ATTENTION the machine will not steer when ±
5km/hour speed is exceeded.
GB
ENGLISH ENGLISH ENGLISH
ENGLISH ENGLISH
(Fig. 1 - 2)