Tabla de contenido
Idiomas disponibles
Idiomas disponibles
13
plug the plug in the socket. Put both hands on the
chainsaw handles. Be sure that the chain can't
touch anything. Operate the ON/OFF switch;
your electric chainsaw is equipped with a soft-start
device. The soft-start allows the motor to start
gradually, allowing gradual chain rotation. The
chain reach his maximum speed after 1-2 sec.;
move the electric chainsaw just forward and avoid
friction between the guide bar sides and the
working piece. The friction can overload the motor;
to turn off the electric chainsaw you have to release
the ON/OFF switch.
Warning: When working, make sure you stand
safely. Always hold your machine with both
hands. The chain can jam, so be always ready
to face this event: the electronic of your
machine allows you to move the machine out,
to free the blade and to continue cutting.
For your safety mantain a firm grip on the handles
with both two hands, as shown in fig.3. Be ready to
face your electric chainsaw movements;
when you complete the cut, switch off your electric
chainsaw and wait till the chain comes to a
complete stop. Then pull the chainsaw;
watch out! The chain
very hot and cause severe burns.
You can perform different kind of works with your electric
chainsaw. Two examples are following:
cutting of hollow bricks, Poroton, tuff etc.:
put the brick on a solid and clear surface;
turn on your machine and let the chain reach his
maximum speed;
with booth hands on the handles, push the spiked
bumpers on the brick to be cutted and push the bar
into the material. If necessary, use the spiked
bumpers as a guide and lever point. Let the
chainsaw do the job. Don't push too much: chain,
guide bar and electric chainsaw work better if are
not overloaded. In normal conditions the cut of a
brick can take 2-3 seconds;
when you finish the cut don't let the chain touch the
ground or other things in the work area;
be careful that the material you're cutting doesn't
collapse on the guida bar during the cut; usually
this doesn't happen but it's better to be careful;
generation of passage, windows, doors, etc. into
lapideus material:
your electric chainsaw can create openings into
bricks wall, hollow bricks wall, tuff wall etc. using
the "plunge cut" technique;
clear the working area;
never start the plunge cut with the guide bar tip;
be sure that on the wall the are no obstacles
according to your electric chainsaw cutting depth;
be sure that no one is behind the wall you're going
to cut;
and the cutting area can be
turn on your machine and let the chain reach his
maximum speed;
with booth hands on the handles, push the bottom
part of the chain on the material to be cut.
Approach using a 30° - 40° angle between the
guide bar and the material;
slowly penetrare the guide bar into the material till
you pass it trough, gradually reduce the angle of
cut;
after 30-40 cm you should have the guide bar
perpendicular to the material;
proceed in your cut activity. Don't overload the
electric chainsaw;
"plunge cut" can be performed horizontaly and
vertically. When you cut horizontaly take care that
the material doesn't push on the guide bar sides.
Cut before horizontaly when you perform doors and
windows openings.
Electronic devices
Your chainsaw is equipped with a CARDI multifunction
electronic device that includes a soft-start and an electronic
clutch:
the soft-start allows the motor to start gradually,
reducing peak current that occurs when you switch
the motor on, helps you when you begin cutting,
allowing gradual chain rotation and avoiding jerks at
the operator's arm. It allows you to use your
chainsaw connected to household electrical outlet.
the electronic clutch cuts off power to the motor in
case of excessive overload, increasing the operator
safety and preventing damage to the motor. When
the overload is over, the device gives back power to
the motor that begins working again;
if the electronic clutch operates frequently means
that the chainsaw is not used properly. Possible
causes can be a not suitable forward speed, an
excessive friction between the bar-side and the
material, excessive cutting depth.
M
a
i
n
t
e
n
a
n
c
e
-
S
M
a
i
n
t
e
n
a
n
c
e
-
S
Periodic maintenance
at the end of the work, after having removed the
blade, blow compressed air inside the rotating
motor in order to remove dust and powder. Do this
operation wearing protective goggles;
before starting any other cleaning, maintenance or
lubrication operation make sure that the chainsaw
is unplugged;
keep your chainsaw clean and dry, in particular its
handles and its moving parts;
never use solvents or other harsh chemicals for
cleaning your chainsaw;
after use put your chainsaw in a dry, safe place
inaccessible to children place;
gears are lubricated by lubricating oil and grease
which are suited for any external temperature. You
don't have to check the oil level or to fill it up.
always unplug the chainsaw during check or blade
replacement;
never unplug the chainsaw by pulling the cord;
English
e
r
v
i
c
e
-
W
a
r
r
a
n
e
r
v
i
c
e
-
W
a
r
r
a
n
t
y
t
y
Tabla de contenido
