Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Adding or taking out laundry
1. Press Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the
relevant step during which the machine was switched into
the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4. Close the Loading Door.
5. Make changes in auxiliary functions, temperature and
speed settings if necessary.
6. Press Start / Pause button to start the machine.
4.16 Cancelling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be cancelled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
Pump function is activated for 1-2 minutes regardless of the
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
C
Depending on the step where the programme was
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
4.17 End of programme
"End" appears on the display at the end of the programme.
1. Wait until the loading door light illuminates steadily.
2. Press On / Off button to switch off the machine.
3. Take out your laundry and close the loading door. Your
machine is ready for the next washing cycle.
4.18 Your machine is equipped with a
"Standby Mode"
In case of not starting any programme or waiting without
making any other operation when the machine is turned
on by On/Off button and while it is in selection step or if
no other operation is performed approximately 2 minutes
after the programme you selected has come to an end,
your machine will automatically switch to energy saving
mode. Brightness of indicator lights will decrease. Also,
if your product is equipped with a display showing the
programme duration, this display will completely turn off. In
case of rotating the Programme Selection knob or pressing
any button, lights and display will restore to their previous
condition. Your selections made while exiting the energy
saving mode may change. Check the appropriateness of
your selections before starting the programme. Readjust if
necessary. This is not a fault.
16 / EN
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
Lift the rear part of the siphon to remove it as illustrated.
C
If more than normal amount of water and softener
mixture starts to gather in the softener compartment,
clean the siphon.
2 Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
3 After cleaning, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
5.2 Cleaning the loading door and the drum
For products with drum cleaning programme, please see
Operating the product - Programmes.
For products without drum cleaning, follow the below steps
to clean the drum:
Select Additional Water or Extra Rinse auxiliary
functions. Use a Cottons programme without pre-wash. Set
the temperature to the level recommended on the
drum cleaning agent which can be provided from
authorized services. Apply this procedure without any
laundry in the product. Before starting the programme,
put 1 pouch of special drum cleaning agent (if the special
agent could not be supplied, put max. 100 g of powder
anti-limescale) into the main wash detergent compartment
(compartment no. "2"). If the anti-limescale is in tablet form,
put only one tablet into the main wash compartment no. "2".
Dry the inside of the bellow with a clean piece of cloth after
the programme has come to an end.
C
Repeat Drum Cleaning process in every 2 months.
Use an anti-limescale suitable for the washing
machines.
Washing Machine / User's Manual
Tabla de contenido
