Pressfit PUMA-RR Manual De Uso página 9

4.2) Enabling/disabling the LED Worklights
To switch on/off during tool operation:
Select the LED option from the "main menu".
LED
ON
Hold down button (6) until a long beep to confi rms
LED
selection.
OFF
4.3) Alarms / Warnings
These appear on the display during operation accompanied by a warning
sound to provide the operator with tool status notifi cations.
LOW BATTERY: replace the battery immediately. When
BATTERY
the battery voltage drops below the minimum safety
level, the tool can no longer be switched on; the tool will
be able to complete any work cycle already in progress.
HIGH BATTERY TEMPERATURE: remove the battery
BATTERY
and wait for it to cool.
SCHEDULED MAINTENANCE RECOMMENDED:
30001
The tool continues to function normally but needs to
be sent for a full Press fi t inspection.
This message, accompanied by a warning sound, is
repeated after 30 s not in use after the every operation
once service has been indicated.
4.4) Error messages
These appear on the display during operation, combined with a beep and
fl ashing LEDs to notify the operator of procedural or operational errors.
Message Error description
Pressing cycle error.
Pressure release button (7)
ERROR
activated before reaching
the set parameters (Force/
Pressure).
Motor current absorption
error.
The tool stops working.
001
Pressure transmitter output
002 voltage out of set range.
Failure to reach calibrated
003
pressure within 30 s of con-
tinuous tool operation.
Battery overload with safety
device activated.
The tool stops working.
004
NOTE: Errors 00.. displayed for about 30 seconds before being reset, but will display repea-
tedly in the event of permanent anomalies.
GB
4.5) Return to original factory settings
To recover the tool's initial factory settings:
Check that every part of the tool is intact before starting any maintenance
work.
The tool is sturdy, completely sealed and does not require any particular at-
tention; to maintain good working order, observe the following precautions:
5.1) Careful cleaning
Dust, sand and dirt can be dangerous to any hydraulic equipment. After
each day of use, the tool must be cleaned with a clean cloth, taking care
to remove all dirt deposits, especially close to moving parts. Avoid the
accumulation of dirt on the thrust rollers and grease them regularly (Fig. o).
Make sure that the motor ventilation system is free from dust and dirt.
Do not use hydrocarbon products to clean rubber parts.
5.2) Storage case
When not in use, store the tool in a dry place inside the sealed plastic
storage case, to protect it from accidental knocks and dust exposure.
The ideal battery storage temperature is between 10°C and 30°C.
Solution
The Press fi t PCS1 storage case is designed to hold the tool and accessories;
Repeat the pressing cycle and
the case size is 714x466x179 mm and it weighs 4.1 kg.
wait for the motor to switch
off automatically.
5.3) Scheduled maintenance
Wait for the display to switch
Upon reaching the preset number of work cycles, the tool will display a
off (60 s) or remove and
warning that scheduled maintenance is required.
reinsert the battery, then
restart to tool. In the event
PUMA-RR and LYNX-RR only: the display indicates
of frequent reoccurrence,
contact Press fi t.
that the set number of work cycles prior to scheduled
maintenance has been reached; this message reappears
Repeat the work cycle. In the
event of frequent reoccur-
after 30 s not in use.
rence, contact Press fi t .
PUMA and LYNX only: after every 15 s not in use, three intermittent
Repeat the work cycle. In the
LED fl ashes and a warning sound indicate that scheduled maintenance
event of frequent reoccur-
rence, contact Press fi t .
is required.
Wait for the display to switch
off (60 s) or remove and
reinsert the battery, then
restart to tool. In the event
of frequent reoccurrence,
contact Press fi t.
inspection, to maintain perfect working order, ensuring operator
safety and reliable results over time.
Select the RESET option from the "main menu".
RESET
SW:S1J78409
Hold down button (6) until a long beep to confi rms
selection.
5. MAINTENANCE
Remove the battery from the tool before carrying out any
type of intervention.
Once the set number of work cycles prior to scheduled
maintenance has been reached, the tool continues to
function normally, however it needs to be sent for a full Press fi t
9
30001