Troubleshooting
CHECK
THESE
POINTS
TO HELP SAVE YOU TIME
AND
MONEY.
Dishwasher
will not fill
• Press the START/Cancel
pad to start the dishwasher.
• Be sure door is latched securely.
• Be sure the water is turned on.
• Check that the pad is properly selected for a cycle.
• Check your home's circuit breaker or fuse box.
• Check inlet hose for a kink.
• Check water valve inlet for sediment and clean if necessary.
Dishwasher
will
not drain/
• If hooked up to a food waste disposer, be sure the knock-out is removed from the
water
in tub bottom
disposer inlet.
• Check for food obstruction in the drain or disposer.
• Check drain hose for a kink.
• Check your home's circuit breaker or fuse box.
• Check that the cycle is completed.
Dishwasher
adds water at
• This is normal. The sensor (select models) in the pump must stay submerged so a
end of cycle
short fill of water is added after the cycle's last drain.
Detergent
cup is not empty
" Check that the cycle is completed.
• Be sure dispenser is not blocked.
• Use fresh detergent stored in a cool, dry place.
Dishwasher
seems noisy
• A water valve hiss during fill is normal.
• Water circulation sounds are normal.
• A thumping sound may be a wash arm bumping an item that is extending beyond the
racks. Readjust load to avoid obstructing wash arm.
• Chopping or grinding sounds may be heard as the internal food disposer chops [lard
items like fruit seeds, nuts, etc.
• Humming during the drain is normal.
• A snap noise is the detergent cup lid hitting the door liner when the dishwasher door
is opened at the end of the cycle. This is normal.
• Proper installation affects the noise level.
Cycle takes too long
• ToughScrubT% ToughScrub
TM
Plus or Sanitized (select models) has been selected
and the cycle is extended to heat water.
• Check to see that the incoming water temperature is 120° F (49° C).
Dishwasher
has an odor
• Run dishes being held in the dishwasher through a Rinse Only cycle (select models).
• Many dishwashers have a "new" smell when first installed. This will dissipate with use.
• Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.)
• For a strong odor, place baking soda in both sides of the detergent cup. Select Light
Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle
by unlatching the door and let it stand overnight. Restart the dishwasher by latching
the door and allow it to complete the cycle. Another alternative is to use a dishwasher
cleaning product such as Jet-Dry Dishwasher Cleaner*.
Dishwasher
leaks
• Check that the dishwasher is level. (Refer to the Installation Instructions.)
• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use
only detergents designed for use in a dishwasher. Less detergent is needed in soft
water. Try another brand of detergent if sudsing continues.
• Follow directions closely on how to add a forgotten item (log. 3).
• To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.
Indicator
lights flashing
• The countdown display (select models) flashes after a cycle is selected until the
START/Cancel
pad is pressed.
• The countdown display (select models) and the delay indicator flash after a delay is
selected until the START/Cancel
pad is pressed.
• All active display indicators flash if the door is opened during a running cycle or delay.
• The currently selected cycle flashes if an attempt is made to change the cycle after
cycle "lock-in".
• The lock indicator flashes and the countdown display (selected models) flashes an "L"
if a pad is pressed while the control lock is enabled.
13
Cont.
*Brand names are trademarks of the respective manufacturer.