Fluid Compatibility; Assembly / Disassembly - FILL-RITE 800C Serie Manual Del Propietário

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

FLUID COMPATIBILITY

The 800C is compatible with the following fluids:
•Diesel Fuel, Gasoline, Kerosene, Mineral Spirits,
Heptane, and Hexane
The 800C is NOT compatible with the following fluids:
•Bleach, Hydrochloric Acid, Ink, Sulfuric Acid, and Salt
Water
If in doubt about compatibility of a specific fluid, contact supplier
of fluid to check for any adverse reactions to the following wetted
materials.
Ryton
Aluminum
EPDM
Flourocarbon
Teflon®

ASSEMBLY / DISASSEMBLY

Meter consists of a chamber housing, measuring chamber,
gear train, counter assembly and cover.
completely disassembled without disturbing piping.
Counter Assembly
For access to counter assembly, remove reset knob (item 3) by
grasping edges and pulling firmly. Remove two screws (item
29) and lift counterface (item 2) and cover (item 1) off. Remove
two screws (item 13) to extract counter (item 4). Reassemble
by reversing procedure.
Meter Chamber Assembly
To expose meter chamber assembly, tilt the meter at least
slightly face down, so that no parts fall out when removing meter
housing. Remove the four screws (item 20), then remove meter
housing (item 19). Meter chamber assembly consists of upper
and lower chambers, a nutating disc and seal gasket.
Reassemble by reversing procedure.
If replacement of any components of the meter chamber
assembly is required, the complete assembly must be
replaced due to the precise method of its construction. This
assures a proper fit and a correctly operating chamber.
Gear Train and Seal
To disassemble gear train and seal, remove gear frame (item
12) by prying slightly. Remove cluster gear (item 10) and
washer (item 11) from shaft (item 9). Remove drive gear (item
8) and washers (item 7) by rotating and pulling drive gear.
Remove O-ring seal (item 6).
When reassembling seal, lubricate O-ring liberally with oil or
petroleum jelly and replace in cover. Place washer on drive gear
shaft. Carefully rotate and push shaft through O-ring and cover
to prevent damage to O-ring. Shaft must then be guided into
pinion bevel (item 28) if counter has not been removed. Replace
remaining parts to complete assembly by reversing
disassembly procedure.
REPAIR
Meters needing repair should be taken to an authorized repair
shop for service. Meters must be thoroughly triple-rinsed before
being taken in for repair.
PRIOR TO SERVICE, ADHERE TO FOLLOWING INSTRUCTIONS:
Meters must be triple-rinsed and accompanied by a note
indicating the chemicals which have been pumped through
the unit. Meters not adhering to these specifications may be
refused service.
Stainless Steel
Buna N
Nickel
Meter can be
800C SERIES STRAINER KIT
* Item 1 not
included in kit.
ITM. PART
NO. NO.
1
800G1325
806C, 1", U.S. Gallon
800G2727
806C, 1", U.S. Gallon, Nickel Plated
800G1387
806C, 1", U.S. Gallon, Teflon® Coated Opt.
800G1998
806C, 1" BSP, Liters
800G2705
806C, 1" BSP, Liters, Nickel Plated
800G1440
806C, 1" BSP, Liters, Teflon® Coated Opt.
2
800F4360
Cover
800F4362
Cover, Nickel Plated
800F4361
Cover, Teflon® Coated
3
800F4380
O-Ring (-131), Buna-N
800F4381
O-Ring (-131), Viton
4
800F4350
Screen
5
800F4320
5/16-18 x 7/8 SHCS
6
800F4340
Strainer Housing
800F4343
Strainer Housing, Nickel Plated
800F4342
Strainer Housing, Teflon® Coated
800F4337
Strainer Housing, BSP Threads
800F4339
Strainer Housing, BSP Threads, Teflon Opt.
800F4338
Strainer Housing, BSP Threads, Nickel Opt.
7
800F4390
1 x 2 Pipe Nipple
8
800F4400
1" Street Elbow
9
700F2800
O-Ring (-218)
700F2801
O-Ring (-218), Viton
TH18
Strainer Kit, 1", U.S. (Includes items 2-6, 9)
TH18T
Strainer Kit, 1", U.S.,Teflon® Ctd. (items 2-9)
TH18X418
Strainer Kit, 1" BSP (Includes items 2-6, 9)
TH18TX418
Strainer Kit, 1" BSP,Teflon Ctd. (items 2-6, 9)
800B/800C SERIES REPAIR PARTS KITS
PART
NO.
DESCRIPTION
800KTG2540
Repair Kit, U.S. Gallon (Standard Seals)
(Includes items 6-12, 18, 22, 24-26, 28)
800KTG2541
Repair Kit, U.S. Gallon (Viton Seals)
(Includes items 6-12, 18, 22, 24-26, 28)
800KTG2542
Repair Kit, Liter (Standard Seals)
(Includes items 6-12, 18, 22, 24-26, 28)
800KTG2543
Repair Kit, Liter (Viton Seals)
(Includes items 6-12, 18, 22, 24-26, 28)
800KTG2579
Repair Kit, U.S. Gallon, (EPDM Seals)
(Includes items 6-12, 18, 22, 24-26, 28)
2
DESCRIPTION
QTY.
1
Opt.
Opt.
Opt.
1
Opt.
Opt.
1
Opt.
1
2
1
Opt.
Opt.
Opt.
1
1
1
Opt.
Tabla de contenido
loading

Este manual también es adecuado para:

806c807c

Tabla de contenido