Programming Device Addresses Using The Programmer - FireClass FC501 Guía Rápida De Instalación

Master panel
Detector: 50
Iloop=073 mA (400ma MAX)
Not addressed dev.> ENT to AUTO-ADDRESS
AUTO ADDRESSING
PLEASE WAIT
AUTO ADDRESSING
Found: 018 detectors,
ENT to DEVICE MAPPING,
DEVICE MAPPING
Evt time type
016 10:15:33 PH L1:---
017 10:17:19 PH L1:---
DEVICE MAPPING
Evt time type
001>10:15:33 PH L1:---< enter the add.
002 10:17:19 PH L1:---
DEVICE MAPPING
Evt time type
--- unique RIM L1:---< enter the add.
--- unique LPAV L2:---
DEVICE MAPPING
Evt time type
--->*active*LPSB L3:---<enter the add.
--- --:--:--LPSB L3:---
Figure 6 - Autoaddressing procedure.
■
Programming Device Addresses Using the
Programmer
As an alternative to the procedure of Auto-addressing
the Installer can use the service tool FC490ST to ad-
dress the devices on Loop.
Connect your detector to the programmer. If you
1.
need to program a sounder or a module, con-
nect the programming lead into the AUX port of
the programmer and the other end of the lead into
the device's programming port

Note you cannot address a detector while the pro-
gramming lead is plugged in.
Press and hold F1 to switch the programmer on.
2.
When prompted, enter the password: F1, F2, F1,
3.
F2, F3, F4.
18
Lev.3: Program
Modules: 44
EXIT
ESC
FAULT PAGE
(not addressable devices)
RUNNING
ESC to exit
ESC
FAULT PAGE
(not addressable devices)
PANEL IS READY TO WORK
END
004 modules
(with the default basic programming)
ESC to exit
ESC
MAIN PAGE
RUNNING 0=stop
add counter 017
0
ESC
DEVICE MAPPING
STOPPED 1=run
add done:000/022 Evt
001>10:15:33 PH L1:089< ENT to config.
002 10:17:19 PH L1:---
DEVICE MAPPING
STOPPED 1=run
Evt
add done:017/022
--->unique RIM
--- unique LPAV L2:---
STOPPED 1=run DEVICE MAPPING
add done:020/022 Evt
--->--:--:--LPSB L3:005<ENT to config.
--- --:--:--LPSB L3:---
FIRECLASS Addressable Fire Control Panel
Notes
"Unique" in the time field indicates that it is the only device of its type on the
loop. For example if only one FC410DDM module is used in the system, it is
tagged as "Unique" so it is not necessary to activate it, the installer knows
where it is.
"Active" in the time field indicates that the relevant device is active, it is
applicable ONLY to output device types such as sounders, beacons and SNM
modules.
When the installer, scanning the list of previously auto-addressed devices,
reaches an output-only device type, this device becomes active (a sounder
starts to sound, a beacon starts to flash, an output module illuminates its
LED) until a new device is selected or the permanent address is entered. In
this way it will be possible to locate where the device is.
EXIT
AT THIS TIME
EXIT
EXIT
MAIN PAGE
STOPPED 1=run
time type add done:001/022
STOPPED 1=run
time type add done:018/022
L1:015< ENT to config.
STOPPED 1=run
time type add done:021/022
Press F2 to enter the address program, this will
4.
show the current address of the device on the
screen (brand new devices will always be 255).
Press F2 to choose the "write" menu option.
5.
Using F3 and F4, change the address to the
6.
required address.
When the correct address is displayed, press F2
7.
to write.
The programmer will display the message: "pro-
8.
grammed ok" and then it will show the next ad-
dress.
Label the device ready for installing.
9.
MS: Det 089 lev.3 :PROGRAM
WORKING MODE Master panel
[First flo ]
MS: MS: Det 089 Det 089 lev.3 :PROGRAM lev.3 :PROGRAM
^
ASSIGNED ZONE DEVICE NAME Master panel Master panel
[First flo ]
MS: Det 089 lev.3 :PROGRAM
^
DEVICE NAME Master panel
[First flo ]
^
MS: Det 015 lev.3 :PROGRAM
TRIGGER ZONE EVENT
[First flo ]
MS: Det 015 lev.3 :PROGRAM
MS: Det 089 lev.3 :PROGRAM
^
TRIGGER ZONE#1 DEVICE NAME Master panel Master panel
[First flo ]
MS: MS: Det 015 Det 089 lev.3 :PROGRAM lev.3 :PROGRAM
^
DEVICE NAME Master panel
TRIGGER ZONE#1 Master panel
[First flo ]
MS: Det 015 lev.3 :PROGRAM
^
DEVICE NAME Master panel
[First flo ]
^
MS: Det 005 lev.3 :PROGRAM
TRIGGER ZONE EVENT Master panel
[First flo ]
MS: MS: Det 005 Det 089 lev.3 :PROGRAM lev.3 :PROGRAM
^
TRIGGER ZONE#1 DEVICE NAME Master panel Master panel
[First flo ]
MS: MS: Det 005 Det 089 lev.3 :PROGRAM lev.3 :PROGRAM
^
DEVICE NAME Master panel
TRIGGER ZONE#1 Master panel
[First flo ]
MS: Det 005 lev.3 :PROGRAM
^
DEVICE NAME Master panel
[First flo ]
^
Master panel
FC501