Technical Data; Scope Of Supply; Electric Data - REMS Power-Press SE Instrucciones De Servicio

eng
Leaking battery fluid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fluid gets into the eyes.
● Observe the safety instructions on the battery and the rapid charger.
● Keep unused batteries away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fire due to short-circuiting.
● Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against short­circuiting, e.g. with a cap. This
reduces the risk of fluids escaping from the batteries.
● Do not throw defective batteries in the normal household waste. Hand the
defective batteries over to an authorised REMS contract service workshop or a
recognised disposal company. Observe the national regulations. See also page
6. Disposal.
● Keep batteries out of reach of children. Batteries can be life threatening if
swallowed, seek medical assistance immediately.
● Avoid contact with leaking batteries. Leaking fluid can cause skin irritation
and burns. Rinse off immediately with water in case of contact. Also consult a
doctor if the fluid gets into the eyes.
● Take the batteries out of the power tool when they are empty. This reduces
the risk of fluids escaping from the batteries.
● Never recharge the non-rechargeable batteries, open them, throw them on
fires or create a short-circuit. The batteries can cause fires and burst. There
is a risk of injury.
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use ear protection
Electrical device complies with protection class II
Environmental friendly disposal
CE conformity mark
1. Technical Data
Intended use
WARNING
REMS radial presses are intended for the purpose of making press joints of all
common pressfitting systems.
REMS cropping tongs are intended for the purpose of cropping threaded bars up to
the strength class 4.8 (400 N/mm²).
REMS cable shears are intended for the purpose of cropping electric cables
≤ 300 mm² (Ø 30 mm).
REMS axial presses are intended for the purpose of making compression sleeve
connections.
REMS pipe expanders are intended for the purpose of expanding and calibrating
pipes.
REMS batteries are intended for supplying energy to the REMS cordless drive units
and the REMS cordless LED lamp. Note voltage of the batteries.
Rapid chargers are intended for charging the REMS batteries.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
Electrical radial presses/pipe expanders: Drive unit, instruction manual, sheet
steel case
Cordless presses/pipe expanders: Drive unit, Li-Ion battery, rapid charger,
instruction manual, sheet steel case
1.2. Article numbers
REMS Power-Press SE drive unit
REMS Power-Press drive unit
REMS Power-Press ACC drive unit
REMS Power-Press XL ACC
REMS Mini-Press ACC drive unit Li-Ion
REMS Mini-Press 22 V ACC drive unit Li-Ion
REMS Akku-Press drive unit Li-Ion
REMS Akku-Press ACC drive unit Li-Ion
REMS Ax-Press 25 ACC drive unit Li-Ion
REMS Ax-Press 25 L ACC drive unit Li-Ion
REMS Ax-Press 30 drive unit Li-Ion
REMS Ax-Press 40 drive unit Li-Ion
REMS Akku-Ex-Press Cu ACC drive unit Li-Ion
REMS Akku-Ex-Press P drive unit Li-Ion
REMS Akku-Ex-Press P ACC drive unit Li-Ion
16
REMS Akku-Ex-Press Q & E ACC drive unit Li-Ion
REMS Power-Ex-Press Q & E ACC drive unit
Expanding device 6 – 40 mm, ½ – 1½"
Expanding device 54 – 63 mm, 2"
REMS battery Li-Ion 14.4 V, 1.5 Ah
REMS battery Li-Ion 14.4 V, 3.0 Ah
REMS battery Li-Ion 21.6 V, 1.5 Ah
REMS battery Li-Ion 21.6 V, 2.5 Ah
Rapid charger Li-Ion/Ni-Cd 230 V
Rapid charger Li-Ion 230 V
Voltage supply Li-Ion 230 V, instead of 14.4 V batteries
Sheet steel case, REMS Power-Press SE
Sheet steel case, REMS Power-Press
Sheet steel case, REMS Power-Press ACC
Transport box XL REMS Power-Press XL ACC
Sheet steel case, REMS Mini-Press ACC / Mini-Press 22 V ACC
Sheet steel case, REMS Akku-Press / REMS Akku-Press ACC
Sheet steel case, REMS Ax-Press 30 / Ax-Press 40
Sheet steel case, REMS Akku-Ex-Press Q & E
Sheet steel case, REMS Ax-Press 25 ACC / Ax-Press 25 L ACC
Sheet steel case, REMS Akku-Ex-Press Cu ACC
Sheet steel case, REMS Akku-Ex-Press P / Akku-Ex-Press P ACC
Sheet steel case, Combi Set REMS Ax-Press 25 ACC
and Akku-Ex-Press P ACC
REMS CleanM
1.3. Capacity
REMS Mini-Press ACC / Mini-Press 22 V ACC Radial press
for making press joints in all standard press fitting systems
on steel pipes, stainless steel pipes, copper pipes, plastic
pipes, composite pipes
Radial presses REMS Power-Press / Power-Press ACC /
Power-Press XL ACC and REMS Akku-Press / Akku-Press ACC
for producing press fittings of all common
press fitting systems on steel pipes, stainless steel
pipes, copper pipes, plastic tubes, composite tubes
Axial presses for making compression sleeve joints (sliding
sleeve joints) on stainless steel pipes, steel pipes, copper
pipes, plastic pipes, composite pipes
REMS Akku-Ex-Press Q & E ACC for expanding of
pipes/coil for the system Uponor Quick & Easy
REMS Power-Ex-Press Q & E ACC for expanding of
pipes/coil for the System Uponor Quick & Easy
REMS Akku-Ex-Press Cu ACC for widening and calibrating
soft copper pipes, soft aluminium pipes, soft precision steel
pipes, soft stainless steel pipes
REMS Akku-Ex-Press P and REMS Akku-Ex-Press P ACC
for widening plastic pipes, composite pipes
Operating temperature range
REMS cordless presses
Battery
Rapid charger
Mains operated presses
Storage temperature range
1.4. Thrust
Thrust of radial presses, without Mini radial press
Thrust REMS Mini-Press ACC / Mini Press 22 V ACC
Thrust REMS Ax-Press 25 ACC
Thrust REMS Ax-Press 25 L ACC
Thrust REMS Ax-Press 30 / Ax-Press 40
Thrust REMS Akku-Ex-Press Cu ACC / P / P ACC / Q&E ACC
Thrust REMS Power-Ex-Press Q & E ACC
The specified forces are nominal forces.
1.5. Electric Data
572101
REMS Power-Press SE
577001
REMS Power-Press
577000
REMS Power-Press ACC
579000
578001 REMS Power-Press XL ACC
REMS Power-Ex-Press Q & E ACC
578002
571003
REMS Mini-Press ACC
571004
REMS Ax-Press 25 ACC / 25 L ACC
573003
REMS Akku-Ex-Press Cu ACC
573004
REMS Akku-Ex-Press P
573008
REMS Akku-Ex-Press P ACC
573006
REMS Akku-Ex-Press Q & E ACC
575006
REMS Mini-Press 22 V ACC
575009
575008 REMS Ax-Press 30
eng
575005
575007
575100
575101
571545
571555
571570
571571
571560
571575
571565
570280
570280
570280
579240
578290
571290
573282
578290
578290
578290
578290
573284
140119
Ø 10 – 40 mm
Ø ⅜ – 1¼"
Ø 10 – 108 mm
Ø ⅜ – 4"
Ø 12 – 40 mm
Ø 16 – 40 mm
Ø ⅜ – 1½"
Ø 16 – 63 mm
Ø ½ – 2"
Ø 8 – 42 mm
Ø ⅜ – 1¾"
Ø 12 – 40 mm
–10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +113 °F)
–10 °C – +60 °C (14 °F – +140 °F)
> 0°C (32 °F)
32 kN
22 kN
20 kN
13 kN
30 kN
20 kN
34 kN
230 V~; 50 – 60 Hz; 450 W; 1.8 A
110 V~; 50 – 60 Hz; 450 W
S3 20% (AB 2/10 min)
all-insulated, interference-suppressed
14.4 V =; 1.5 Ah
14.4 V =; 3.0 Ah
21.6 V =; 1.5 Ah / 21.6 V =; 2.5 Ah