Safety Instructions For Batteries; Technical Data; Explanation Of Symbols; Instruction Manual - REMS Cento Instrucciones De Servicio

eng
● Never leave the pipe cutting machine running unattended. Switch off the
pipe cutting machine during longer work breaks and pull out the mains plug/
battery. Electrical devices can cause hazards which lead to material damage or
injury when left unattended.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the pipe cutting
machine safely may not use this pipe cutting machine without supervision
or instruction by a responsible person. Otherwise there is a risk of operating
errors and injuries.
● Only allow trained persons to use the pipe cutting machine. Apprentices
may only use the pipe cutting machine when they are over 16, when this is
necessary for their training and when they are supervised by a trained operative.
● The pipe cutting machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge unless they have been given supervision or
instruction concerning the use of the pipe cutting machine by a person
responsible for their safety. Children must be supervised to ensure that they
do not play with the pipe cutting machine.
● Check the power cable of the pipe cutting machine and extension leads
regularly for damage. Have these renewed by qualifi ed experts or an authorised
REMS customer service workshop in case of damage.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m w cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm². cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².

Safety instructions for batteries

WARNING WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.

1. Technical data

Use for the intended purpose
WARNING WARNING
REMS Cento, REMS Cento RF, REMS Akku-Cento 22 V and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes.
All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMS Cento Basic:
REMS Cento RF Set:
REMS Akku-Cento 22 V Basic: Cordless pipe cutting machine, Li-Ion 21.6 V, 5.0 Ah battery, Li-Ion rapid charger, ring spanner size SW 27/17, instruction manual.
REMS DueCento Basic:
1.2. Article numbers
Pipe cutting machine
REMS cutting wheel Cu-INOX for pipes of the press fi tting systems of
stainless steel, copper, carbon steel
REMS cutting wheel Cu especially for pipes
of the press fi tting systems of copper
REMS cutting wheel St for steel pipes, cast pipes (SML)
REMS cutting wheel C-SF especially for pipes of the press fi tting systems/
push fi tting systems of carbon steel, simultaneously produces a chamfer
REMS cutting wheel V, s 10, for plastic and composite tubes,
wall thickness s ≤ 10 mm
REMS cutting wheel P, s 21, for plastic and composite tubes,
wall thickness s ≤ 21 mm
REMS cutting wheel RF
REMS battery Li-Ion 21.6 V, 5.0 Ah
REMS battery Li-Ion 21.6 V, 9.0 Ah
Rapid charger Li-Ion 230 V, 90 W
Feed lever REMS DueCento
Spring plug
Base frame
Base frame, movable
Roller, pack of 4
Rollers INOX (pack of 4) of tubular stainless steel
Roller, pack of 4
Roller insert for cutting pipes Ø 40 – 100 mm
Ring spanner size 27/17
REMS Herkules 3B, material rest with tripod
REMS Herkules Y, material rest with clamping device
REMS Herkules XL 12"
Height adjustable pipe rest 1, Ø 40 – 110 mm, Ø 1½ – 4"
Height adjustable pipe rest 1, Ø 100 – 225 mm, Ø 4 – 8"
Height adjustable pipe rest 2, Ø 40 – 110 mm, Ø 1½ – 4"
REMS Jumbo E, folding workbench
REMS Jumbo, folding workbench
REMS REG 10 – 54 E, outside/inside pipe deburrer
REMS REG 28 – 108, inside pipe deburrer
Marking device for marking the insertion depth for fi ttings on pipes
REMS CleanM, machine cleaner
Pipe cutting machine, ring spanner size 27/17, instruction manual.
Pipe cutting machine, ring spanner size 27/17, one each of pipe guides Ø 75 mm and 110 mm, operating instructions.
Pipe cutting machine, ring spanner size 27/17, 2 height adjustable pipe rests 1 for pipes Ø 100 – 225 mm, Ø 4 – 8",
feed lever, spring plug, instruction manual.
Save all warnings and instructions for future reference.
See also www.rems.de → Downloads → Instruction Manuals.

Explanation of symbols

WARNING WARNING Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use ear protection
Electrical device complies with protection class II
Not suitable for using outdoors
Environmental friendly disposal
CE conformity mark
REMS Cento REMS Cento RF
845000 845006
845050
845053
845052
845055
845051
845054
845218 845218
089082 089082
849315 849315
849310 849310
845118
845110
845119
849112 849112
120120 120120
120130 120130
120125 120125
845220
120240 120240
120200 120200
113835 113835
113840
845530
140119 140119
REMS Akku-Cento 22 V REMS DueCento
845007
845050
845053
845052
845055
845051
571581
571583
571585
845218
089082
849315
849310
845118
845110
849112
120120
120130
120125
845220
120240
120200
113835
113840
845530
140119
eng
845005
845050
845053
845052
845055
845051
845057
845218
089082
845060
849112
845220
845230
140119
13