General Power Tool Safety Warnings - REMS Cento Instrucciones De Servicio

eng
Translation of the Original Instruction Manual
Fig. 1– 10
1 Cutting wheel drive
2 Cutting wheel
3 Rollers
4 Holes for stand
(REMS Cento / REMS Cento RF /
REMS Akku-Cento 22 V)
5 Pipe
6 Feed lever
7 Safety foot switch
8 Spindle
9 Spring plug
10 Height adjustable pipe rest

General power tool safety warnings

WARNING WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the pres-
ence of fl ammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distrac-
tions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodi-
fi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplug-
ging the power tool. Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when oper-
ating a power tool. Do not use a power tool while you are tired or under
the infl uence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protec-
tive equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your fi nger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
clothing away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust extraction and collec-
tion facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
12
11 Clamping lever
12 REMS REG 28-108
13 REMS REG 10-54 E
14 Roller insert for cutting pipes
Ø 40 – 110 mm (accessory,
REMS DueCento)
15 Pipe guide (Cento RF)
16 Cylinder head screws
17 Stand
18 Machine status check
19 Battery
20 Graduated charging state display
c) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding
of moving parts, breakage of parts and any other condition that may affect
the power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control
of the tool in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fi re when used
with another battery pack.
b) Use power tools only with specifi cally designated battery packs. Use of any
other battery packs may create a risk of injury and fi re.
c) When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fi re.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, fl ush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is damaged or modifi ed. Damaged or
modifi ed batteries may exhibit unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or excessive temperature.
Exposure to fi re or temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specifi ed in the instructions. Charging
improperly or at temperatures outside the specifi ed range may damage the battery
and increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) Never service damaged battery packs. Service of battery packs should only
be performed by the manufacturer or authorized service providers.
Safety instructions for pipe cutting machines
WARNING WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
● Do not use the pipe cutting machine if it is damaged. There is a danger of accident.
● Do not overload the pipe cutting machine, the cutting wheel (2) and the
pipe by too high feeding pressure on the feed lever (6). The pipe cutting
machine and the cutting wheel are subject to heavier wear by too high feeding
pressure and can be damaged. At too high feeding pressure, the ends of the
pipe to be cut are pressed further inwards causing constriction of the cross section.
Pipes made of brittle material, e.g. cast pipes, can be fractured or broken by too
high feeding pressure.
● Do not reach into moving parts in the cutting and deburring area and in the
area of the rollers (3) and height adjustable pipe rests (10). There is a risk
of injury by crushing fi ngers or hands.
● Use REMS Herkules 3B (Art. No. 120120), REMS Herkules Y (Art. No. 120130),
REMS Herkules XL 12" (Art.-No. 120125) material rest(s) or the height adjust-
able pipe rest(s) (Fig. 6 (10)) to support long pipes at both ends if necessary
and align these exactly to the rollers (3) of the cutting machine. This reduces
untrue running and uncontrolled falling to the ground.
● Check that the pipes are running true before cutting them. Cutting pipes that
are not straight causes imbalance and the pipe or pipe rest can fall over. The
pipe can also slip off the material or pipe rest, the pipe cutting machine can move
and the cutting wheel can be damaged. Danger of injury.
● Only move or carry the REMS Cento / REMS Cento RF / REMS Akku-Cento
22 V / REMS DueCento by the feed lever (6) when this has been locked as
described in 2.2. If the feed lever is not locked there is a danger that the feed lever
(6) will come away from the spindle (8). REMS Cento / REMS Cento RF /REMS
Akku-Cento 22 V /REMS DueCento can then fall over or fall off. Danger of injury.
● Protect yourself and persons accompanying the work against the rotating
pipe during cutting. There is a risk of injury.
eng