Recovery Process; Battery Replacement; Spare And Wearing Parts - Bosch DCU 100 Instrucciones De Funcionamiento

en 22 | DCU 100 | Maintenance
6. Maintenance
6.1 Cleaning
6.1.1 DCU 100
Only use a soft cloth and neutral detergents to clean
the housing and display of the DCU 100. Do not use
abrasive cleaning agents and coarse workshop cloths.
6.1.2 Data carrier
Clean the CD-ROM or DVD-ROM with a disk cleaning kit
or carefully wipe over the silver side of the disk with a
soft, lint-free cotton cloth. Never use paper towels, as
these could cause scratches.
6.1.3 DVD drive
Clean the DVD drive at regular intervals with a cleaning
disk for the CD-ROM or DVD drive. The appropriate
cleaning disks are available from most computer or
entertainment electronics shops.
6.2

Battery replacement

WARNING - Risk of explosion on charging
battery!
Risk of explosion and hence burns and injury
in the event of inexpert charging of the
battery.
¶
Only use the battery specified for the
DCU 100.
¶
Only use the power supply unit specified
for the DCU 100.
¶
Heed the notes on disposal.
¶
Batteries are not to be heated, burnt,
short-circuited, mechanically damaged or
charged with excessively high currents or
reverse polarity.
¶
Suitable extinguishing agents: Water, CO
sand.
1. Switch off the DCU 100.
2. Slacken off the battery screws on the back of the
DCU 100 (see Fig. 3, Pos. 3).
3. Remove the battery.
4. Insert the new battery in the battery compartment
and secure by means of the two screws on the bat-
tery (see Fig. 3, Pos. 3).
5. Switch on the DCU 100.
i
The battery charge indicator can be called up using
the icon.
"
The battery charge indicator shows the current battery
charge on a scale of 0 to 100 %.
i
It is advisable to charge the battery for at least three
hours before running the DCU 100 off the battery.
|
1 689 989 174 2015-03-25
6.3

Recovery process

!
All data and applications on the hard disk will be
erased during the recovery process!
1. Connect the DCU 100 to the power supply unit.
2. Switch on the DCU 100.
3. Connect the external DVD drive to the DCU 100 by
way of the USB connecting cable (0.6 m).
4. Insert the recovery DVD 1 687 005 082 in the DVD
drive.
5. Re-start Windows with "START >> RE-START".
 Windows is started.
6. Confirm the dialog window "
want to recover your System? WARNING!
ALL DATA ON HARD DISK DRIVE C: WILL BE
LOST. Please be patient while recovery
process is running.
 DCU 100 recovery is started – duration approx.
25 minutes.
 Windows is re-started on completion of recovery
 The dialog window "
covery media from the device and
click "OK" to reboot the computer
appears.
7. Take the recovery DVD out of the DVD drive.
8. Remove the external DVD drive.
9. Confirm with <OK>.
"
This completes the recovery process.
i
Then re-install ESI[tronic] 2.0.
6.4

Spare and wearing parts

,
2
Designation
DCU 100 tablet PC (green)
DCU 100 tablet PC (anthracite)
Battery
<)
External DVD-ROM drive
Power supply unit
Power cord
Touch pen (3x)
Wearing part
<)
Would you really
" with <Yes>.
Please remove the re-
"
Order number
1 687 023 687
1 687 023 688
1 687 335 042
1 687 023 698
1 687 023 697
1 684 461 186
1 687 010 403
Robert Bosch GmbH