Cleaning, Maintenance And Ordering Spare Parts - EINHELL TE-CD 12/1 X-Li Manual De Instrucciones Original

All 3 LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit
The battery has an adequate remaining charge.
Red LED is lit:
The battery is empty, recharge the battery.
6.8 LED lamp (Fig. 1/Item 10)
The LED light (10) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (10) will come on
automatically as soon as you press the On/Off
switch (4).
6.9 Changing the bit (Fig. 7)
Caution! Set the changeover switch (3) to its cen-
ter position whenever you carry out any work (for
example changing the tool, maintenance work,
etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (9) with an automatic
spindle stop.
•
Open the chuck (9). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
•
Tighten the chuck (9) and then check that the
tool is secure.
6.10 Screwdriving
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw. Set the torque to suit the screw size as
specifi ed in the instructions.
6.11 Integrated magnetic bit mount (Fig. 8-9/
Item 11)
The cordless drill/screwdriver has an integrated
magnetic bit mount (11) for ¼ inch (6.35mm) bit
inserts.
To use it, remove the quick-change drill chuck (9)
by pressing the rear drill chuck sleeve (b) towards
the quick-change drill chuck.
You can now plug a suitable bit insert into the in-
tegrated magnetic bit mount (11).
To fi t the quick-change drill chuck (9) again, slide
it onto the bit mount (11) as far as it will go while
Anl_TE_CD_12_1_X_Li_SPK9.indb 21 Anl_TE_CD_12_1_X_Li_SPK9.indb 21
GB
pressing the drill chuck sleeve (b). Then release
the drill chuck sleeve. The quick-change drill
chuck will lock automatically. Check whether the
quick-change drill chuck is secure.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always pull out the power plug or take out the
rechargeable battery before starting any cleaning
work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Tip! For good results we
recommend high-quality ac-
cessories from
www.kwb.eu
[email protected]
- 21 -
!
16.10.2019 15:06:22 16.10.2019 15:06:22