Replay; Storage Locations M1 - M6; Calling Up A Message By Remote Control - Monacor PA-1120DMT Instrucciones Instalación Y Funcionamiento

6.2 Replay

Use the control LEVEL (16) to adjust the volume
of the messages replayed . Prior to the first mes-
sage replay, turn the control approx . to mid-
position and, if required, adjust the control during
replay . If the volume of the insertion module is
too low for the amplifier used even though the
control has been turned to the right stop, the
output level may be increased by another 10 dB
( ☞ chapter 5 .4) .
If an emergency message is to be replayed
automatically, make absolutely sure to prevent
any inadvertent readjustment of the control .
Headphones can be used to monitor a stored
message: Connect the headphones (minimum
impedance: 64 Ω) to the jack PHONES (3) [mono,
only the left side for stereo headphones]; the out-
put (26) to the amplifier will be muted .
6.2.1 Storage locations M1 – M6
The following description applies to the normal
replay mode . Please refer to chapter 6 .2 .1 .1 for
the immediate replay mode .
For one-time replay of a message that has
been recorded on one of the storage locations
"M1" to "M6":
1) Press the button (15) of the storage location
desired . The display will show, for example:
M3 Rep2
PlayMode
2) Press the button START/ STOP (14) . The replay
will start and
Playing
lower display line .
3) To stop the replay, press the button START/ STOP
again .
For multiple replay of a recorded message:
1) Press the button of the storage location de-
sired . The display will show, for example:
(storage location M3,
M3 Rep2
replayed twice)
PlayMode
2) Use the button UP (12) or DN (11) to define the
number of message repeats:
replayed 1 to 9 times,
tinuously .
3) Press the button REPEAT/ STOP (13) . The replay
will start and
Playing
lower display line .
will appear on the
to
Rep1 Rep9
= repeated con-
Rep0
will appear on the
4) To stop the replay, press the button
REPEAT/ STOP again .
At a zone paging microphone PA-2400RC,
PA-1120RC or PA-6000, it is also possible to select
a message M1 – M6 and then to start the replay by
means of the button START/ STOP or to start mul-
tiple replay by means of the button REPEAT/ STOP .
6.2.1.1 Immediate replay
If immediate replay has been selected by means
of the jumper PLAY MODE SELECTOR (
ter 5 .2):
1) Press the button (15) of the storage location
desired . The display will now show, for ex-
ample:
1)
M3 Rep2
Playing
The (multiple) replay will start immediately . The
number of replays will be indicated next to the
storage location .
2) To stop the replay, press the button REPEAT/
STOP (13) .
3) When the replay has been stopped, the button
UP (12) or DN (11) can be used to change the
number of message repeats:
to
Rep1 Rep9
= repeated continuously .
Rep0

6.2.2 Calling up a message by remote control

Instead of the buttons of the insertion module
(cf . chapter 6 .2 .1), the switching contacts on the
connection plate (18) can be used to replay the
messages that have been recorded on the storage
locations "M1" to "M6": Briefly connect the ter-
minal with the name of the corresponding button
(M1, ... M6, START [/STOP], REPEAT [/STOP]) to the
terminal GND (via a normally open contact) . The
number of repeats for multiple message replay,
however, can only be changed via the buttons UP
(12) and DN (11) .
Use the terminal BUSY to externally indicate
insertion module activity [analogous to the LED in-
=
dicator (27) on the circuit of the insertion module
that lights up when a message is being recorded
or replayed] . In this case, the terminal will provide
3,3 V ⎓ against GND, and an LED, for example,
can be connected via a suitable series resistor
( fig . 5, page 20) .
☞
☞
(storage location M3,
replayed twice)
= replayed 1 to 9 times,
chap-
19