HIKOKI C 10FCH2 Instrucciones De Manejo página 21

11. Bevel cutting procedures (Fig. 19 and Fig. 20)
(1) Loosen the clamp lever and bevel the saw blade to the
left.
(2) Adjust the bevel angle to the desired setting
while watching the bevel angle scale and indicator,
then secure the clamp lever.
WARNING
○ When the workpiece is secured on the left or right side
of the blade, the short cut-off portion will come to rest
on the right or left side of the saw blade. Always turn the
power off and let the saw blade stop completely before
raising the handle from the workpiece.
If the handle is raised while the saw blade is still rotating,
the cut-off piece may become jammed against the saw
blade causing fragments to scatter about dangerously.
○ When stopping the bevel cutting operation halfway,
start cutting after pulling back the motor head to the
initial position.
Starting from halfway, without pulling back, causes the
safety cover to be caught in the cutting groove of the
workpiece and to contact the saw blade.
12. Compound cutting procedures
Compound cutting can be performed by following the
instructions in 9 and 10 above. For maximum dimensions
for compound cutting, refer to "SPECIFICATIONS"
table.
CAUTION
○ Always secure the workpiece with the right hand side
for compound cutting. Never rotate the table to the
right for compound cutting, because the saw blade
might then contact the clamp or vise that secures the
workpiece, and cause personal injury or damage.
13. Cutting long materials
When cutting long materials, use an auxiliary platform
which is the same height as the holder (optional
accessory) and base of the special auxiliary equipment.
Capacity: wooden material (W × H × L)
120 mm × 40 mm × 1000 mm
14. Installing the holders (Optional accessory)
The holders help keep longer workpieces stable and in
place during the cutting operation.
(1) As indicated in Fig. 21, use a steel square for aligning
the upper edge of the holders with the base surface.
Loosen the 6 mm wing nut. Turn a height adjustment
bolt 6 mm, and adjust the height of the holder.
(2) After adjustment, fi rmly tighten the wing nut and fasten
the holder with the 6 mm knob bolt (optional accessory).
If the length of Height Adjustment Bolt 6 mm is
insuffi cient, spread a thin plate beneath. Make sure the
end of Height Adjustment Bolt 6 mm does not protrude
from the holder.
15. Stopper for precision cutting (Stopper and holder
are optional accessory)
The stopper facilitates continuous precision cutting in
lengths of 280 mm to 450 mm.
To install the stopper, attach it to the holder with the
6 mm wing bolt as shown in Fig. 22.
16. Confi rmation for use Crown molding vise, Crown
molding Stopper (L) and (R) (Optional accessory)
(1) Crown molding Stopper (L) and (R) (optional
accessories) allow easier cuts of crown molding without
tilting the saw blade. lnstall them in the base both-sides
side to be shown in Fig. 23. After inserting
tighten the 6 mm knob bolts to secure the Crown
molding Stoppers.
(2) The crown molding vise (B) (Optional accessory) can
be mounted on either the left fence (Fence (B)) or the
right fence (Fence (A)). lt can unite with the slope of the
crown molding and vice can be pressed down.
Then turn the upper knob, as necessary, to securely
attach the crown molding in position. To raise or lower
the vise assembly, fi rst loosen the 6 mm wing bolt.
After adjusting the height, fi rmly tighten the 6 mm wing
bolt; then turn the upper knob, as necessary, to securely
attach the crown molding in position (See Fig 24).
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT
EDGE against the Crown molding Stoppers as shown in
Fig. 24. Adjust the Crown molding Stoppers according
to the size of the crown molding.
Tighten the 6 mm wing bolt to secure the Crown molding
Stoppers.
WARNING
○ Always fi rmly clamp or vise to secure the crown molding
to the fence; otherwise the crown molding might be
thrust from the table and cause bodily harm.
Do not bevel cutting. The main body or saw blade may
contact the sub fence, resulting in an injury.
CAUTION
○ Always confi rm that the motor head (see Fig. 1) does
not contact the crown molding vise assembly when it
is lowered for cutting. If there is any danger that it may
do so, loosen the 6 mm knob bolt and move the crown
molding vise assembly to a position where it will not
contact the saw blade.
MOUNTING AND DISMOUNTING SAW BLADE
WARNING
○ To prevent an accident or personal injury, always turn
off the trigger switch and disconnect the power plug
from the receptacle before removing or installing a
blade.
If cutting work is done in a state where the bolt is not
suffi ciently tightened, the bolt can get loose, the blade
can come off , and the lower guard can get damaged,
resulting in injuries.
Also, check that the bolts are properly tightened before
plugging the power plug into the receptacle.
○ If the bolts are attached or detached using tools other
than the 10 mm box wrench (standard accessory),
excessive or improperly tightening occurs, resulting in
injury.
1. Mounting the saw blade (Fig. 25, Fig. 26, Fig. 27
and Fig. 28)
(1) Rotate the lower guard (plastic) to the top position.
(2) Use the driver to loosen the 4 mm screw fastening the
spindle cover and then remove the spindle cover.
(3) Press in spindle lock and loosen bolt with 10 mm box
wrench (standard accessory).
Since the bolt is left-hand threaded, loosen by turning it
to the right as show in Fig. 27.
NOTE
○ If the spindle lock cannot be easily pressed in to lock the
spindle, turn the bolt with 10 mm box wrench (standard
accessory) while applying pressure on the spindle lock.
The saw blade spindle is locked when the spindle lock
is pressed inward.
(4) Remove the bolt and washer (B).
(5) Lift the lower guard and mount the saw blade.
WARNING
When mounting the saw blade, confi rm that the rotation
indicator mark on the saw blade and the rotation
direction of the gear case (see Fig. 1)are properly
matched.
(6) Thoroughly clean washer (B) and the bolt, and install
them onto the saw blade spindle.
English
21