Care And Maintenance - Chicco POLLY SWING UP Instrucciones De Uso

or equivalent to the type recommended for
the correct function of this product. (for the
remote control: LR03-AAA; for the vibration
block: LR20-D; for the side fixture: LR14-C).
• The use of rechargeable batteries is not rec- ommended as the product may not work
properly.
• Rechargeable batteries must only be re-
charged under adult supervision.
• Rechargeable batteries must be removed
from the product during recharging.
• Remove the batteries from the product be-
fore disposing of the product.
• Always keep batteries and tools out of the
reach of children.
• To replace batteries: loosen the screw on the
battery compartment cover with a screw-
driver and open the cover. Then remove the
spent batteries and fit new ones, ensuring
that they have been fitted in the correct po-
larity (as shown on the product), replace the
battery cover, and tighten the screw.
This product complies with the Directive
2012/19/EU.
The crossed bin symbol on the appliance indicates
that the product, at the end of its life, must be dis-
posed of separately from domestic waste, either
by taking it to a separate waste disposal site for
electric and electronic appliances or by returning
it to your dealer when you buy another similar ap-
pliance. The user is responsible for taking the appliance to a special
waste disposal site at the end of its life. If the disused appliance is
collected correctly as separate waste, it can be recycled, treated
and disposed of ecologically; this avoids a negative impact on
both the environment and health, and contributes towards the re-
cycling of the product's materials. For further information regard-
ing the waste disposal services available, contact your local waste
disposal agency or the shop where you bought the appliance.

CARE AND MAINTENANCE

Fabric composition
LINING COVER: All new materials. Outer cover: 100% polyester. Pad-
ding: 100% polyester.
BOOSTER CUSHION: All new materials. 100% polyester outer cover.
100% polyester padding.
TOY: All new materials. 100% polyester.
• This product requires periodic maintenance.
• The cleaning and maintenance operations must only be carried
out by an adult.
• Periodically inspect the swing to check for broken, torn or miss-
ing parts: if this is the case, do not use it.
• Please refer to the care label for instructions on how to wash the
fabric parts.
Hand wash in cold water
Do not bleach
30° C
Do not use a dryer
Do not iron
Do not dry clean
• Check that the fabric and stitching are in good condition each
time you wash it.
• Prolonged exposure to direct sun light or heat may cause the
fabric to fade or parts to deform.
Clean the frame structure with a damp cloth and neutral deter-
gent. Do not soak the frame in water.
REMOVABLE COVERS
• Remove the tray by pressing the two orange side buttons whilst
pulling it upwards.
• Remove the head rest and booster cushion, slide out the harness
straps through their holes.
• Slide the waist strap out through the plastic rings located at the
bottom of the seat.
• Unhook all the elastic rings from the plastic hooks on the bottom
side of the seat. Now remove the harness straps fastened to the
bottom of the fabric backrest, sliding them through the slots on
the outer edge of the seat. Now undo the zip, slide the upper
straps through the padding and remove the fabric part.
• To refit the cover on the frame, repeat the above procedure in
the reverse order, making sure that you hook all the elastic rings
back onto their relative hooks to ensure the padding is fastened
correctly to the frame.
COMPONENTS
a. Top tube of the seat
b. Frame connection tubes
1. Side sun hood hooks
c. Side fixture X (with remote control)
1. Battery compartment
d. Side fixture Y
e. Front and rear legs
f. Seat
1. Side backrest adjuster button
2. Vibration block
3. Fabric crotch strap
4. Side compartment for the connection tube
5. Connection fixture for the dual tray
g. Dual tray
1. Side button
2. Rigid crotch strap
3. Tray
4. Second tray
h. Booster seat
i. Waist strap
j. Upper harness strap
k. Remote control
l. Sun hood
m. Toys
ASSEMBLING THE FRAME
1. Grasp the front and rear legs, and insert them into the X and Y
fixtures on the tubes, as seen in Diagram 1. When the legs are
assembled correctly, the metal pins will slot into the holes on
the fixture tubes. At this point you will hear them click into place.
2. Press the fixture side buttons (Diagram 2) and open the frame by
pushing the front and rear legs apart. The seat can now be fitted.
ASSEMBLING THE SEAT
3. Open the zip on the back of the fabric backrest as far as possible
(Diagram 3) and slide the upper seat tube into the slots inside
the backrest, as seen in Diagram 4. Make sure you hear the metal
pins click into place.
4. Thread the upper harness straps through the slots in the back-
rest (Diagram 5). Now cover the upper tube with the fabric and
close the zip (Diagram 6).
5. Hook all the elastic rings onto the plastic hooks on the bottom
of the seat (Diagram 7).
WARNING: Check that the seat fabric is fitted correctly before using
the swing.
6. Take hold of the connection tubes on the seat frame (compo-
nent b) and insert the round shaped end into the slots at the side
of the seat (Diagram 8), making sure that the side hooks on the
sun hood are facing inwards towards the swing. Make sure you
20