Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Driving OnSlopes
Refer to the SLOPE GAUGE on page 8 to help determine
slopes
where you may operate the tractor
safely.
i_ll
WARNING!
Do not mow on inclines with a slope in
excess of 15 degrees (a rise of approximately
2-1/2
feet every 10 feet). The tractor could overturn
and
cause serious injury.
Mow up and down slopes, NEVER across.
Exercise extreme
caution
when changing
direction
on
slopes.
Watch for holes, ruts, bumps, rocks, or other hidden
objects.
Uneven terrain could overturn
the machine. Tall
grass can hide obstacles.
Avoid turns when driving
on a slope. Ira turn must be
made, turn down the slope. Turning
up a slope greatly
increases the chance of a roll over.
Avoid stopping
when driving
up a slope. If it is necessary
to stop while driving
up a slope, start up smoothly
and
carefully
to reduce the possibility
of flipping
the tractor
over backward.
Engagingthe ParkingBrake/
Settingthe CruiseControl
NOTE:The
parking
break and cruise control are controlled
by
the same lever. If using the brake when engaging
the parking
brake/cruise
control
lever, the parking
brake will engage.
If using
the drive pedal when engaging
the parking
brake/cruise
control
lever, the cruise control
will engage.
Parking Brake
NOTE:The
parking
brake must be set if the operator
leaves the
seat with the engine
running
or the engine will automatically
shut off.
To set the parking
brake:
1.
Press the brake pedal completely
down with your left foot
and hold it in that position.
2.
Push the parking
brake/cruise
control
lever downward
and
hold it in that position.
3.
Remove your foot from the brake pedal.
4.
Release pressure from the parking
brake/cruise
control
lever.
After completing
step 3, the brake pedal should
remain in the
down position.
If it doesn't,
the parking
brake is not engaged.
Repeat steps 1 through
4 to engage the parking
brake.
To disengage
the parking
brake, lightly
press the brake pedal.
WARNING!
Never leave a running
machine
unattended.
Always disengage
PTO, set parking
brake, stop engine and remove
key to prevent
unintended
starting.
Cruise Control
_
ARNING!
Never engage
the cruise control
lever
while traveling
in reverse.
To set
1.
2.
3.
4.
the cruise control:
Slowly press the upper portion
of the drive pedal with your
right foot until the desired speed is achieved.
Lightly
press the parking
brake/cruise
control
lever
downward
and hold it in that position.
Remove your foot from the drive pedal.
Release pressure from the parking
brake/cruise
control
lever.
After completing
step 3, the drive pedal should
remain in the
down position
and the tractor
will maintain
the same forward
speed. If it doesn't, the cruise control
is not engaged.
Repeat
steps 1 through
4 to engage
the cruise control.
To disengage
the cruise control,
lightly
press the drive pedal or
the brake pedal.
NOTE: Cruise control
can not be set at the tractor's
fastest
ground
speed. If the operator
should
attempt
to do so, the
tractor will automatically
decelerate
to the fastest optimal
mowing
ground
speed.
To change the direction
of travel from forward
to reverse when
cruise control
is engaged,
press the brake pedal to disengage
the cruise control and bring the tractor
to a complete
stop. Then
slowly press the reverse pedal with the ball of your foot to travel
in reverse.
Usingthe DeckLift Lever
To raise the cutting
deck, move the deck lift lever to the left, then
place it in the notch best suited for your application.
Operatingthe Headlights
The lamps are ON whenever
the ignition
key is rotated out of
the STOP position.
The lamps turn OFF when the ignition
key is
moved to the STOP position.
Engagingthe PTO
Engaging
the PTO transfers
power to the cutting
deck or other
(separately
available)
attachments.
To engage
the PTO:
1.
Move the throttle
control
lever to the FAST (rabbit)
position.
SECTION
S --
OPERATION
17
Tabla de contenido
