Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Control unit
"Set clock/timer" symbol
Timer symbol
Aroma Perfection symbol
Time button
Taste
Time/switch-on time +
Aroma Perfection +
Setting the current time
After connecting the mains plug to a socket, 12:00 and the word SET appears on the display (6). The
clock uses the 24-hour format. Set the current time by pressing the + and - buttons. Confirm the time
by pressing the timer button (
).
"SET" appears in the display until the time is confirmed. If no buttons are pressed for 15 seconds, the
appliance automatically switches to standby and sets the time to midday (12:00).
Note: The clock must be reset after a power failure, after the mains plug has been unplugged, or when
switching to summer/winter time.
The correct time can be set by pressing and holding down the timer button (
appears on the display (6). Use the + and - buttons to set the time. Confirm the time by pressing the
timer button (
).
Programming the switch-on time
Note: Please make sure that the current time has been set before programming the timer.
The device's automatic switch-on starts the brewing process automatically at the desired time. The
switch-on time can be programmed up to 24 hours in advance. This can be shown by pressing the
timer button (
) once. The switch-on time and the timer symbol (
(6).
Set the desired switch-on time by pressing the + and - buttons. "SET" appears on the display. Confirm
the set time by pressing the timer button (
).
Note: Confirm the switch-on time within 15 seconds, otherwise the settings will not be saved.
Note: The clock must be reset after a power failure, after the mains plug has been unplugged, or when
switching to summer/winter time.
14
Display (6)
Descaling symbol
Taste
Time/switch-on time -
Descale „-"
On/off button with control
lamp (7)
) for 3 seconds. "SET"
) then appear on the display
Coffee preparation
Open the water tank (4) by swinging open the water tank lid (1). Pour the desired amount of cold
water into the water tank (4).
Caution: When using the thermal beaker (9), ensure that you fill the water tank (4) only to the "MAX"
mark, otherwise the coffee might overflow and cause scalding.
The water-level indicator (5) applies to the amount of cold water needed to brew the desired number
of cups of coffee (@ 125ml). Close the water tank lid (1). Open the filter (3) by flipping the filter lid
(2) upwards.
Take a size 2 paper filter, fold over the stamped edge and place it into the filter (3). The paper filter
should not protrude over the edge of the filter. If necessary, push it down slightly with your hand.
Add the required amount of ground coffee.
Note: Depending on your personal taste, use approx. 5-7g of medium-fine ground coffee per cup. If
the coffee is ground too finely, the filter (3) may overflow.
Close the filter lid (2). Stand the thermal jug (8) or thermal mug (9) on the device.
Now insert the mains plug into the socket.
Immediate start
If the coffee is to be prepared immediately, press the on/off button (7), the preparation starts. You can
stop the brewing process at any time by pressing the stop button (7).
Caution: Danger of scalding through remaining coffee in the filter. Wait a few minutes before remov-
ing the thermal jug/beaker.
Note: After the brewing cycle has finished, the control lamp (7) switches off after a few minutes. This
indicates that no larger quantities of coffee are left in the filter (3) and the thermal jug/beaker can be
removed. A drip-stop valve prevents subsequent dripping.
Automatic switch-on
If coffee brewing should start automatically at the programmed switch-on time, press the timer but-
ton (
). The currently set switch-on time appears on the display. Use the + and - buttons to set the
time at which you want brewing to start. Confirm this within 5 seconds by pressing the on/off button
(7). The current time appears on the display (6).
Note: When automatic switch-on is activated, all the other keys are disabled. The appliance's auto-
matic switch-on function can be deactivated by pressing the on/off button (7) again.
WMF Aroma Perfection
The WMF Aroma Perfection function can be activated to brew stronger, more aromatic coffee. It is
particularly recommended for preparing smaller amounts. To do this, press the Aroma ("+") button.
The
symbol appears on the display (6). Now start the brewing process using the on/off button (7).
Please note that the preparation time is slightly longer.
Stand the thermal jug or thermal mug on the device.
You can cancel brewing at any time by pressing the on/off button (7) again.
Wait a few minutes until all of the coffee has run into the thermal jug/beaker. A drip-stop valve
prevents coffee dripping when you remove the thermal jug/beaker.
Automatic shut-off
The automatic shut-off function prevents overheating when the device is in use. The appliance
switches itself off after a few minutes and the control lamp on the on/off button (7) extinguishes
when all the water has passed through. The appliance may be switched off prematurely by pressing the
on/off button (7) . This may be necessary, for example, if you accidentally start the appliance without
water.
Note: You must wait for a few minutes before removing the thermal jug/beaker or pouring water into
the hot device. Allow the coffee machine to cool beforehand.
15
Tabla de contenido
